GENUINE SU HS STAYUP FLOAT KIT
WZX1304

£19.60 exc vat

£23.52 inc vat

Out of stockOut of stock
The new adjustable height StayUp® Float is resistant to modern ethanol based Fuels and has a military spec closed cell construction making it puncture proof. The ability to adjust the Float Arm allows for quick and easy minor alterations to Float lev...

£19.60 exc vat

£23.52 inc vat

Out of stockOut of stock

Kit contained products

Paper gasket for the float bowl of any HS2/HS4/HS6 carbs.

People also bought products

Fitted to HIF38 and HIF44 carbs, ethanol tolerant product. Bigger bodied valve.

For turbo models see WZX1095 .Quantity required-1

throttle spindle kit for single HS4 type carbs-.Quantity required-1 kit. -the butterfly is available seperately as WZX1323 for plain-WXZ1325 with air valve

spindle and fixings only for the HS2 carb-the butterfly for this is WZX1320.

sorry folks but buying both kits you get double the gaskets

This is the original type of needle valve that governs the plastic fuel float in your SU carb.

An alternative better upgraded version is available as CA90.

The metal washer AUD2193 goes up against this seal on the jet where it enters the float bowl on all HS type carbs.

Standard spring for all HS2 and HS4 on minis except for the 997/998 Cooper from 1964-9 and H4 special tuning carbs which used AUC4587.

Complete with screw the choke trunnion is used on nearly all SU carb linkages.

See ACC5062 for carb cable link trunnion also.

Early single HS" carbs had these splendid looking brass top dashpot dampers which are interchangeable with the plastic type.

These screws fit all HS type carb butterflies to hold them on the throttle spindle

Worn throttle spindles cause erratic performance from your carb and sometimes the housing gets worn--These are the bushes to repair worn carbs when replacing spindles for HS2 carbs. As a guidline 0.250" internal diameter and ream carb bo...

Float grommet for the mini twin HS2/4 carbs---this 30 degree angle is for the L/H ( front) carb and is positioned to angle the float bowl--Used on both twin HS2/4 carbswhen using correct mini inlet manifolds- Midgets and MGB used different angles,u...

Pin to hold the accelerator cable which locates in the carb bracket lever. Supplied as originally fitted with washers, nut and split pin plus a proper machined hole for the cable unlike many others on the market- which come either bare or with wrong ...

The pin that holds the float bowl in place on the float bowl lid-See also AUE266 for complete lid with float bowl and needle valve fitted.

Fits single and twin HS2 carb dashpots but only single HS4 carbs(the twin HS$ use AUC8114) --See AUC8103HB for the original brass type fitted to early single HS2"

Float grommet for the mini twin HS2/4 carbs---this 30 degree angle is for the R/H ( rear) carb and is positioned to angle the float bowl--Used on both twin HS2/4 carbswhen using correct mini inlet manifolds-Midgets and MGB used different angles,usual...

Worn throttle spindles cause erratic performance from your carb and sometimes the housing gets worn--These are the bushes to repair worn carbs when replacing spindles for HS4 carbs. As a guideline 0.3125" internal diameter ream body to 9...

Paper gasket for the float bowl of any HS2/HS4/HS6 carbs.

If fuel is overflowing the float bowl the needle valve is leaking. This may be caused by the float WZX13040(GSU200) being misadjusted, stuck or leaking OR the needle may be fouled with a bit of grit or worn and not sealing. This is an

altern...

Clip for holding the choke cable on the HS carb abutment bracket 12G766.