CARBURETTOR LEVER PIN
ACC5062

£2.93 exc vat

£3.52 inc vat

In stockIn stock
Pin to hold the accelerator cable which locates in the carb bracket lever. Supplied as originally fitted with washers, nut and split pin plus a proper machined hole for the cable unlike many others on the market- which come either bare or with wrong type washers.

See AUE34 also for choke cable trunnion

£2.93 exc vat

£3.52 inc vat

In stockIn stock

Recommended usage 1 x ACC5062 to fit one mini.
Emission, Carburettor Fittings and engine controls - Qty 1
Carburettor Fixings, Throttle Pedal & Abutment Br - Qty 1

Recommended products

Standard Mini throttle cable, fitment from 1959 through to 1990 and all HS carbed minis. Not suitable for cars with HIF38, HIF44, SPI and Twin point.

Complete with screw the choke trunnion is used on nearly all SU carb linkages.

See ACC5062 for carb cable link trunnion also.

Our heavy duty throttle cable is superior in many ways.

A nylon interior ensures smooth operation. The outer cable is 32mm longer and inner is 95mm longer than the standard one.

Cable to carb bolt is ACC5062.

Kit products

This fitting kit suits all later day 1.25" and 1.5" twin carb set ups where the balance rods between the carbs required are equal length (2.25"), some early carbs had the balance bar with a triangular plate that were a shorter length. The kit has the...

This is the kit supplied with our C-AHT772, C-AHT773 & C-AHT774 range of alloy inlet manifolds for the weber.

Amal carburettor kit for the Arden 8-Port head. Complete with carbs, manifolds and linkage.

Not Built up= A Complete kit of HS4 CARBS/ MANIFOLD/LINKAGE LESS AIR CLEANER

Not built up-A matching pair of HS2 twin carbs with polished dashpot covers plus original type twin HS2 linkage kit, inlet manifold but less air cleaners etc.

The UNC bolt holding the abutment bracket on the inlet m...

Not built up-A matching pair of HS2 twin carbs with polished dashpot covers and stainless steel heatshields plus original type twin HS2 linkage kit, inlet manifold but less air cleaners etc.

The UNC bolt holding the...

People also bought products

The new adjustable height StayUp® Float is resistant to modern ethanol based Fuels and has a military spec closed cell construction making it puncture proof. The ability to adjust the Float Arm allows for quick and easy minor alterations to Float lev...

spindle and fixings only for HIF44, only with one end threaded as opposed to WZX1128 which is threaded both ends-see WZX1183 for disc

Fitted to HIF38 and HIF44 carbs, ethanol tolerant product. Bigger bodied valve.

For turbo models see WZX1095 .Quantity required-1

throttle spindle kit for single HS4 type carbs-.Quantity required-1 kit. -the butterfly is available seperately as WZX1323 for plain-WXZ1325 with air valve

spindle threaded both ends for HIF44 for most late carbs--see WZ1127 for spindle with thread one end only as per early metro cars. Thread size is 1/4 BSF

spindle and fixings only for the HS2 carb-the butterfly for this is WZX1320.

sorry folks but buying both kits you get double the gaskets

jet assembly (0.100") for the HIF44 carb only- see MGM10008 for HIF38(0.090")

This is the original type of needle valve that governs the plastic fuel float in your SU carb.

An alternative better upgraded version is available as CA90.

spindle to hold the float to the float lid on the bottom of HIF carbs only.

the float is WZX1509A and needle valve is WZX1099A except turbo which is WZX1095

The metal washer AUD2193 goes up against this seal on the jet where it enters the float bowl on all HS type carbs.

Standard spring for all HS2 and HS4 on minis except for the 997/998 Cooper from 1964-9 and H4 special tuning carbs which used AUC4587.

Complete with screw the choke trunnion is used on nearly all SU carb linkages.

See ACC5062 for carb cable link trunnion also.

Early single HS" carbs had these splendid looking brass top dashpot dampers which are interchangeable with the plastic type.

These screws fit all HS type carb butterflies to hold them on the throttle spindle

Worn throttle spindles cause erratic performance from your carb and sometimes the housing gets worn--These are the bushes to repair worn carbs when replacing spindles for HS2 carbs. As a guidline 0.250" internal diameter and ream carb bo...

Float grommet for the mini twin HS2/4 carbs---this 30 degree angle is for the L/H ( front) carb and is positioned to angle the float bowl--Used on both twin HS2/4 carbswhen using correct mini inlet manifolds- Midgets and MGB used different angles,u...

The pin that holds the float bowl in place on the float bowl lid-See also AUE266 for complete lid with float bowl and needle valve fitted.

Fits single and twin HS2 carb dashpots but only single HS4 carbs(the twin HS$ use AUC8114) --See AUC8103HB for the original brass type fitted to early single HS2"

Float grommet for the mini twin HS2/4 carbs---this 30 degree angle is for the R/H ( rear) carb and is positioned to angle the float bowl--Used on both twin HS2/4 carbswhen using correct mini inlet manifolds-Midgets and MGB used different angles,usual...