CHOKE CABLE TRUNNION ACH9042 NIPPLE & 53K3503 SCRE...
AUE34

£2.03 exc vat

£2.44 inc vat

In stockIn stock
Complete with screw the choke trunnion is used on nearly all SU carb linkages.

See ACC5062 for carb cable link trunnion also.

£2.03 exc vat

£2.44 inc vat

In stockIn stock

Recommended usage 1 x AUE34 to fit one mini.
Control Cables, Heater Valves & Heater Radiators - Qty 1
Emission, Carburettor Fittings and engine controls - Qty 1
Carburettor Fixings, Throttle Pedal & Abutment Br - Qty 1

Recommended products
CHOKE CABLE RUBBER TYPE PULL & TWIST UP TO 1987
21A2329

Choke cable up to 1987. Pull & twist to lock..

The grommet in the body for this cable to pass through is CAM5969.

£11.25 exc vat

£13.50 inc vat
Kit products
TWIN CARB LINKAGE KIT
MSSK009

This fitting kit suits all later day 1.25" and 1.5" twin carb set ups where the balance rods between the carbs required are equal length (2.25"), some early carbs had the balance bar with a triangular plate that were a shorter length. The kit has the...

£26.23 exc vat

£31.48 inc vat
AMAL CARB KIT FOR 8-PORT HEAD
C-AJJ4083

Amal carburettor kit for the Arden 8-Port head. Complete with carbs, manifolds and linkage.

£1,474.29 exc vat

£1,769.15 inc vat
TWIN HS2 CARBURETTOR KIT - LESS A/C
FZX3052

Not built up-A matching pair of HS2 twin carbs with polished dashpot covers plus original type twin HS2 linkage kit, inlet manifold but less air cleaners etc.

The UNC bolt holding the abutment bracket on the inlet m...

£1,146.05 exc vat

£1,375.26 inc vat
TWIN HS2 CARBURETTOR KIT WITH S/STEEL HEATSHIELD
FZX3052A

Not built up-A matching pair of HS2 twin carbs with polished dashpot covers and stainless steel heatshields plus original type twin HS2 linkage kit, inlet manifold but less air cleaners etc.

The UNC bolt holding the...

£1,147.79 exc vat

£1,377.35 inc vat
People also bought products
NEEDLE GUIDE LOCKING SCREW HIF44
AUD4252

Screw for holding the needle guide on HIF44, HIF38 carburettors. Also fits HS6.

£4.53 exc vat

£5.44 inc vat
GENUINE SU HS STAYUP FLOAT KIT
WZX1304

The new adjustable height StayUp® Float is resistant to modern ethanol based Fuels and has a military spec closed cell construction making it puncture proof. The ability to adjust the Float Arm allows for quick and easy minor alterations to Float lev...

£19.60 exc vat

£23.52 inc vat
SPINDLE KIT HIF44-EARLY METRO
WZX1127

spindle and fixings only for HIF44, only with one end threaded as opposed to WZX1128 which is threaded both ends-see WZX1183 for disc

£15.78 exc vat

£18.94 inc vat
FLOAT NEEDLE/SEAT FOR HIF38/44 LARGER TYPE VALVE
WZX1099A

Fitted to HIF38 and HIF44 carbs, ethanol tolerant product. Bigger bodied valve.

For turbo models see WZX1095 .Quantity required-1

£20.43 exc vat

£24.52 inc vat
SPINDLE KIT HS4 1.5"
WZX1177

throttle spindle kit for single HS4 type carbs-.Quantity required-1 kit. -the butterfly is available seperately as WZX1323 for plain-WXZ1325 with air valve

£13.50 exc vat

£16.20 inc vat
SPINDLE KIT HIF44
WZX1128

spindle threaded both ends for HIF44 for most late carbs--see WZ1127 for spindle with thread one end only as per early metro cars. Thread size is 1/4 BSF

£43.59 exc vat

£52.31 inc vat
CARB SPINDLE KIT 1.1/4" HS2
WZX1310

spindle and fixings only for the HS2 carb-the butterfly for this is WZX1320.

sorry folks but buying both kits you get double the gaskets

£11.70 exc vat

£14.04 inc vat
HIF44 JET ASSEMBLY
WZX1453A

jet assembly (0.100") for the HIF44 carb only- see MGM10008 for HIF38(0.090")

£25.76 exc vat

£30.91 inc vat
FLOAT NEEDLE VALVE HS2/4/6 (VITON TIPPED)
WZX1100A

This is the original type of needle valve that governs the plastic fuel float in your SU carb.

An alternative better upgraded version is available as CA90.

£10.38 exc vat

£12.46 inc vat
FLOAT SPINDLE HIF
CUD2082

spindle to hold the float to the float lid on the bottom of HIF carbs only.

the float is WZX1509A and needle valve is WZX1099A except turbo which is WZX1095

£4.93 exc vat

£5.92 inc vat
CARB JET TO FLOAT BOWL SEAL
AUD2194

The metal washer AUD2193 goes up against this seal on the jet where it enters the float bowl on all HS type carbs.

£1.01 exc vat

£1.21 inc vat
CARB SPRING (RED 4.5oz) HS TYPE CARBS
AUC4387

Standard spring for all HS2 and HS4 on minis except for the 997/998 Cooper from 1964-9 and H4 special tuning carbs which used AUC4587.

£7.59 exc vat

£9.11 inc vat
ORIGINAL BRASS TYPE CARB DASHPOT DAMPER
AUC8103HB

Early single HS" carbs had these splendid looking brass top dashpot dampers which are interchangeable with the plastic type.

£29.03 exc vat

£34.84 inc vat
BUTTERFLY SCREW
AUC1358

These screws fit all HS type carb butterflies to hold them on the throttle spindle

£0.90 exc vat

£1.08 inc vat
CARB HS2 SPINDLE REPAIR BUSH
AUD3079

Worn throttle spindles cause erratic performance from your carb and sometimes the housing gets worn--These are the bushes to repair worn carbs when replacing spindles for HS2 carbs. As a guidline 0.250" internal diameter and ream carb bo...

£4.16 exc vat

£4.99 inc vat
CARB FLOAT GROMMET 30° L/H FOR HS2/4 (orange)
AUC1316

Float grommet for the mini twin HS2/4 carbs---this 30 degree angle is for the L/H ( front) carb and is positioned to angle the float bowl--Used on both twin HS2/4 carbswhen using correct mini inlet manifolds- Midgets and MGB used different angles,u...

£10.19 exc vat

£12.23 inc vat
CARBURETTOR LEVER PIN
ACC5062

Pin to hold the accelerator cable which locates in the carb bracket lever. Supplied as originally fitted with washers, nut and split pin plus a proper machined hole for the cable unlike many others on the market- which come either bare or with wrong ...

£2.93 exc vat

£3.52 inc vat
FLOAT LID SEAL FOR HIF CARB
AUD3588A

Seal for the HIF38/44 float lid chamber

£1.95 exc vat

£2.34 inc vat
FLOAT PIN
AUC1152

The pin that holds the float bowl in place on the float bowl lid-See also AUE266 for complete lid with float bowl and needle valve fitted.

£0.68 exc vat

£0.82 inc vat
CARB DASHPOT DAMPER
AUC8103A

Fits single and twin HS2 carb dashpots but only single HS4 carbs(the twin HS$ use AUC8114) --See AUC8103HB for the original brass type fitted to early single HS2"

£23.52 exc vat

£28.22 inc vat