TWIN CARB LINKAGE KIT
MSSK009

£26.23 exc vat

£31.48 inc vat

In stockIn stock
This fitting kit suits all later day 1.25" and 1.5" twin carb set ups where the balance rods between the carbs required are equal length (2.25"), some early carbs had the balance bar with a triangular plate that were a shorter length. The kit has the original type abutment bracket that fits to the inlet manifold to guide the accelerator cable.2 pairs of throttle and choke rod levers and a seperate lever for the accelerator cable. The course thread UNC bolt is for the abutment bracket to manifold but will have to be shortened to the correct length for all our late type manifolds. One lever is also supplied for throttle lever but if you are looking for original HS2 centre rod with balance bar see 12A310.

£26.23 exc vat

£31.48 inc vat

In stockIn stock

Recommended usage 1 x MSSK009 to fit one mini.

Recommended products
ACCELERATOR CABLE NYLON SLEEVED EXTRA LONG
C-AHT85

Our heavy duty throttle cable is superior in many ways.

A nylon interior ensures smooth operation. The outer cable is 32mm longer and inner is 95mm longer than the standard one.

Cable to carb bolt is ACC5062.

£6.10 exc vat

£7.32 inc vat
Kit contained products
LINKAGE ROD FOR TWIN CARB LINKAGE
AUC1457

Rod with chamfered ends about 57.2mm long(shorten to 54mm for twin HS4) which has AUE586 and AUE587 clamps on to fit between SU twin carbs for the linkage. Quantity of One is usually required per set up plus a 12A31...

£2.15 exc vat

£2.58 inc vat
THROTTLE BRACKET ON MANIFOLD FOR TWIN CARBS
AEG349

Accelerator bracket for twin carb models, mounts to inlet manifold.

£5.47 exc vat

£6.56 inc vat
TWIN CARB SPINDLE LEVER LH
AUE587

This is the left hand linkage lever that sits on the rods between HS type twin carbs.sold individually

£1.87 exc vat

£2.24 inc vat
WASHER PLAIN 1/4" x 1/2"
GFK1113

£0.08 exc vat

£0.10 inc vat
CARBURETTOR LEVER PIN
ACC5062

Pin to hold the accelerator cable which locates in the carb bracket lever. Supplied as originally fitted with washers, nut and split pin plus a proper machined hole for the cable unlike many others on the market- which come either bare or with wrong ...

£2.93 exc vat

£3.52 inc vat
TWIN CARB SPINDLE LEVER RH
AUE586

This is the right hand linkage lever taht sits on the rods between HS type twin carbs. Sold individually

£1.87 exc vat

£2.24 inc vat
CHOKE CABLE TRUNNION ACH9042 NIPPLE & 53K3503 SCRE...
AUE34

Complete with screw the choke trunnion is used on nearly all SU carb linkages.

See ACC5062 for carb cable link trunnion also.

£2.03 exc vat

£2.44 inc vat
NUT PLAIN 1/4" UNF
GFK3211

£0.07 exc vat

£0.08 inc vat
BOLT 1/4"x3/4"UNC LONG FOR C-AJJ4006
GHF160

Bolt used in our anti roll bar kit and for holding plate on speedo drive housing on gearbox

£0.13 exc vat

£0.16 inc vat
LEVER FOR LINKAGE 001
HAR002

£2.05 exc vat

£2.46 inc vat
People also bought products
VITON TIPPED FLOAT NEEDLE VALVE FOR HS CARBS
VZX1100

This is the original type of needle valve that governs the plastic fuel float in your SU carb.

An alternative better upgraded version is available as CA90.

£9.75 exc vat

£11.70 inc vat
RETURN SPRING KIT FOR HS4
WZX1335

Return spring kit for HS4 carburettor spindle.

£7.65 exc vat

£9.18 inc vat
LEVER FOR LINKAGE 001
HAR002

£2.05 exc vat

£2.46 inc vat
ANCHOR TAG ON CARB
12A4

£0.66 exc vat

£0.79 inc vat
CARB HIF38/44 ABUTMENT BRACKET
CAM4942

Metal bracket that fits between the manifold and the HIF44 (1.75")carb to hold the cable - the choke cable clip for this bracket is CZK6491. Also for HIF38. For HS4 carb see 12G766 bracket. Original Turbo type [...

£11.93 exc vat

£14.32 inc vat
STUD HS4/HIF CARB + some 12G103 HOUSING (5/16")
CHS2514

Universal stud made for fitting the HS4/HIF carb to the manifold (except HS6 with alloy spacer on cast one piece manifold which requires CHS2515 (5.8mm longer)) and it also fits the cylinder head to take the thermostat housi...

£0.78 exc vat

£0.94 inc vat
MANIFOLD STUD FOR TWIN HS2 INLET
CHS2614

Originally quoted as the HS2 twin carb manifold stud it is one thread longer than CHS2613 which was for single HS2 and spin on oil filter head to the block. UNC course thread for manifold or block and UNF for th...

£1.83 exc vat

£2.20 inc vat
HEAT SHIELD BLACK KIT TWIN HS2
MSSK008

Twin carb HS2 (1.25")black heatshields with link bar and 3 new return springs.

£26.47 exc vat

£31.76 inc vat
15" BRAIDED PETROL PIPE 1/4" BORE
PPK6

Before the days of Aeroquip, Minis were fitted with braided steel rubber fuel lines. They should be used in place of rubber for all fuel lines in the engine compartment. They come made to length, with rubber end caps. 1/4" bore size.

Orange ...

£4.24 exc vat

£5.09 inc vat
HEATER AND CHOKE CABLE CLIP HIF CARB
CZK6491

Clip on the heater valve for heater cables on vehicles from 1990 where the in line remote heater valve was used. It has also been used as a clip for HIF carbs to hold the cable but the one from Rover is 13H3472.

£1.35 exc vat

£1.62 inc vat
10" BRAIDED PETROL PIPE 1/4" BORE
PPK4

Before the days of Aeroquip, Minis were fitted with braided steel rubber fuel lines. They should be used in place of rubber for all fuel lines in the engine compartment. They come made to length, with rubber end caps. 1/4" bore size.

Orang...

£4.00 exc vat

£4.80 inc vat
HIF44/HIF6 CARB ELBOW GASKET
GUG705576GM

GASKET BETWEEN CARB AND AIR CLEANER ALLOY ELBOW

£0.38 exc vat

£0.46 inc vat
THROTTLE CABLE ABUTMENT BAR ASS. (ARDEN EIGHT-PORT...
DR002

£42.00 exc vat

£50.40 inc vat
HEAT SHIELD STAINLESS STEEL KIT HS4 TWIN CARBS
MSSK1006

Stainless steel twin HS4 heatshields kit. Comes with Link bar and springs.

£30.71 exc vat

£36.85 inc vat
THROTTLE RETURN SPRING FOR TWIN CARBS
AEC2075

Throttle return springs for all twin carb variants. Usually 3 fitted.

£1.28 exc vat

£1.54 inc vat
TWIN CARB SPINDLE LEVER RH
AUE586

This is the right hand linkage lever taht sits on the rods between HS type twin carbs. Sold individually

£1.87 exc vat

£2.24 inc vat
HEAT SHIELD BLACK KIT HS4 TWIN CARBS
MSSK1004

Pair of heatshield brackets and cross bar

these are made similar to the original cooper HS2 design but ARE for HS4 (1.5")carbs and include the 3 correct springs that attach to the bridging bar for choke return linka...

£29.27 exc vat

£35.12 inc vat
GASKET 1.25" HS2 CARB (GUG705831GM)
1G2624B

Manifold to carb gasket for HS2 single and twin carbs, usually 3 per carb required.

£0.47 exc vat

£0.56 inc vat
"T" PIECE 1/4" SU TWINS MTP001
12H889

Used in petrol fuel lines to take 1/4" petrol hoses it is used mainly on twin carb set ups for petrol being diverted to the 2 carbs.

£4.50 exc vat

£5.40 inc vat
ACCELERATOR RETURN SPRING FOR HS2/4 CARB
1E5537

This throttle return spring fitted every HS2/4 single SU carb and also on the twins as fitted by the factory. Twin carbs used AEC2075 for choke return. Total length 90mm.

£1.90 exc vat

£2.28 inc vat