STUD FOR THERMOSTAT HOUSING WITHOUT SANDWICH PLATE...

CHS2515

£0.65 exc vat

£0.78 inc vat

In stock

Probably the most changed stud on the mini. This is the length used on every A series engine until the introduction of the sandwich plate when longer ones were required. A stainless steel variety C-STR286 is available which we do recommend if you intend on keeping your car as it will save lots of hassle in the future as the standard ones always corrode. 5/16"unc and unf at nut end, this stud is 1.9375"long.

This stud originally replaced CHS2514 but is 2-3 threads(5mm) longer on the end the nut fits which means it might have to be shortened for use on manifolds for fitting carbs so CHS2514 is advised.

Also used on inlet manifold for HIF carb and the block for mechanical fuel pump mounting.

£0.65 exc vat

£0.78 inc vat

In stock

Recommended usage 3 x CHS2515 to fit one mini.

Block Components & Pistons - Qty 2

Cylinder Head 850CC, 998CC & 1100CC Pre 'A' Plus - Qty 3

997CC & 998CC Cooper Cylinder Head - Qty 3

Cylinder Head, 998CC, 'A' Plus 1980 on - Qty 3

Cylinder Head Cooper 'S' 970CC, 1071CC & 1275CC - Qty 3

1275 Except Cooper 'S' & Turbo - Qty 3

Cylinder Head 1275 Turbo & Heads with Triple Coll - Qty 3

Fuel Pumps & Petrol Pipe - Qty 2

Engine and Block 998cc - Qty 2

Engine and Block 1275cc - Qty 2

Water Pump and thermostat - Pre 1996 Not MPI - Qty 3

Recommended products

NUT PLAIN 5/16" UNF

GFK3212

Zinc plated 5/16" UNF plain nut

£0.09 exc vat

£0.11 inc vat

WASHER PLAIN 5/16"

GFK1114

5/16" flat plain washer.

£0.06 exc vat

£0.07 inc vat

SPRING WASHER 5/16"

GFK1125

£0.11 exc vat

£0.13 inc vat

Alternative products

THERMOSTAT STAINLESS STEEL STUD

CHS2515S

S/Steel equivalent of CHS2515.

SEE KITS ALSOC-STR281 AND C-STR286

£1.92 exc vat

£2.30 inc vat

THERMOSTAT HOUSING STAINLESS STEEL STUD AND NUT KI...

C-STR281

Minispares own stainless steel Thermostat housing stud kit for the single tier type thermostat housing.Quantity required one kit per car

£11.00 exc vat

£13.20 inc vat

Kit products

CYLINDER HEAD 8 PORT ARDEN BUILT UP PLUS PUSH RODS

C-AJJ4064

The original Special Tuning head 8 port head by Jim Whitehouse is the ULTIMATE Push rod head for the "A"Series but is NOT A STRAIGHT BOLT ON PART.

It is supplied fully assembled with springs/top caps,Evo collets and utilizes the original siz...

£2,075.04 exc vat

£2,490.05 inc vat

AMAL CARB KIT FOR 8-PORT HEAD

C-AJJ4083

Amal carburettor kit for the Arden 8-Port head. Complete with carbs, manifolds and linkage.

£1,474.29 exc vat

£1,769.15 inc vat

TWIN HS4 CARBURETTOR KIT - LESS AIR FILTERS

FZX3054

Not Built up= A Complete kit of HS4 CARBS/ MANIFOLD/LINKAGE LESS AIR CLEANER

£1,159.23 exc vat

£1,391.08 inc vat

THERMOSTAT HOUSING FITTING KIT (SINGLE TIER TYPE)

12G103FK

This thermostat housing fitting kit, suitable for all single tier thermostat housings. Comes with new studs, nuts, washers and Klinger thermostat housing gasket

£3.35 exc vat

£4.02 inc vat

CYLINDER HEAD ANCILLARY STUD AND NUT KIT PRE 1990

MSSK061

Complete stud, nut and washer kit for the cylinder head ancillaries. Kit contains parts to retain the following:

Inlet/Exhaust manifold to head, studs/nuts/washers

Thermostat housing (no sandwich plate) studs/nuts/washers

H...

£14.00 exc vat

£16.80 inc vat

CYLINDER HEAD 8 PORT ARDEN LARGE VALVE PLUS PUSH R...

C-AJJ4064RACE

The original Special Tuning head 8 port head by Jim Whitehouse is the ULTIMATE Push rod head for the "A"Series has now been revamped and made available with larger inlet valves and special seats available to special order.Ports and combustion chamber...

£2,519.12 exc vat

£3,022.94 inc vat

SPI TO HIF44 CARB CONVERSION KIT

C-STN23

To convert a standard UK spec Single Point Injection car to HIF44 carb. This kit includes wiring looms,fuel tank,fuel pump, carb, air filter and inlet manifold.

£1,424.57 exc vat

£1,709.48 inc vat

People also bought products

ROCKER ADJUSTING NUT EN24T

C-AHT450

Mini Spares genuine upgraded part. Hexagon head rocker screw nut in EN24T.

Also available is a flanged nut C-AHT449

£2.64 exc vat

£3.17 inc vat

HEAD STUD AND NUT KIT WITH A+ FLANGED NUTS

C-AHT279A

This kit of head studs is the best available for road and lightly tuned engines. See the C-AHT280 set for highly tuned engines.

The material spec is alloy steel heat treated to 75 tensile tons per square foot minimum and finish...

£51.92 exc vat

£62.30 inc vat

ARP 11 STUD HEAD SET

C-AHT283

ARP Head stud kit that compromises of;

4 x Long Head Studs

7 x Short Head Studs (Disregard 2 if you're using a 9 stud application)

11 x Multipoint ARP nuts

11 x Heavy Duty Washers

4 x Rocker post studs <...

£142.50 exc vat

£171.00 inc vat

8 PORT HEAD STUD AND NUT SET (STUDS EN24 CHROME MO...

C-AHT282

EN24 Nickel Chrome moly steel studs,Competition head stud kit.

torque to 45ftlbs -no need to re-torque cometic type head gaskets.

For use on the 2012 onwards heads only.

£58.76 exc vat

£70.51 inc vat

CYLINDER HEAD ANCILLARY STUD AND NUT KIT PRE 1990

MSSK061

£14.00 exc vat

£16.80 inc vat

MANIFOLD STAINLESS STEEL STUD AND NUT KIT

C-STR282

Minispares own stainless steel manifold stud and 6 sided hexagon nut kit.

For mutipopint nut kit see C-STR287

Quantity required one kit per car

£21.41 exc vat

£25.69 inc vat

THERMOSTAT HOUSING STAINLESS STEEL STUD AND NUT KI...

C-STR281

Minispares own stainless steel Thermostat housing stud kit for the single tier type thermostat housing.Quantity required one kit per car

£11.00 exc vat

£13.20 inc vat

THERMOSTAT HOUSING FITTING KIT (SINGLE TIER TYPE)

12G103FK

This thermostat housing fitting kit, suitable for all single tier thermostat housings. Comes with new studs, nuts, washers and Klinger thermostat housing gasket

£3.35 exc vat

£4.02 inc vat

CYLINDER HEAD BOLT COOPER S

AEG248

A true Cooper S engine has 10 studs and one specially designed bolt.

£11.17 exc vat

£13.40 inc vat

STUD HS4/HIF CARB + some 12G103 HOUSING (5/16")

CHS2514

Universal stud made for fitting the HS4/HIF carb to the manifold (except HS6 with alloy spacer on cast one piece manifold which requires CHS2515 (5.8mm longer)) and it also fits the cylinder head to take the thermostat housi...

£0.78 exc vat

£0.94 inc vat

STAINLESS STEEL HEATER TAP STUD SET

C-STR285

replacements in stainless steel for the heater tap elbow on the cylinder head.

Quantity required one kit per car

£4.00 exc vat

£4.80 inc vat

ROCKER COVER CHROME FITTING NUT / ERA BUMP STOP NU...

GM038P

Chrome Rocker bolt with UNF thread. Original Rocker cover bolts are dull zinc coated or painted but the chrome type look much better and cheaper.

A longer threaded version CAM6823 was used on prestige Minifin alloy type A series...

£4.20 exc vat

£5.04 inc vat

BLANKING PLUG INLET MANIFOLD & CYL HEAD

ADP210

This 5/8unf steel hexagonal head blanking plug was made for the inlet manifolds where the servo union can be fitted, plus blanking off the thermal transmitter hole under the thermostat. Uses 1B3664 washer ----------please note this will ...

£3.57 exc vat

£4.28 inc vat

CHROME FIXINGS FOR ROCKER COVER

SAC71L

A simple way to dress up that engine compartment while at the same time insuring all the proper hardware is in place. A kit includes 2 each of British made chrome sleeve nuts, spacers and special cup washers, Fits all A & B series engines.

F...

£13.49 exc vat

£16.19 inc vat

ROCKER COVER BLUE T BAR KIT

SAC71BLUE

Anodised in blue for that different look.

£12.00 exc vat

£14.40 inc vat

ROCKER COVER T BARS(PAIR)

SAC71

Originally marketed by minispares in the mid 70s so many companies copied them because of their smart looks and ease of fitment they were improved by offsetting the arms to help tighten plus stop the arm falling out when they were straight. These T b...

£6.75 exc vat

£8.10 inc vat

ROCKER ADJUSTING NUT 1/2" AF NUT SIZE

NT605061

The larger 5/16 unf size rocker screw as used on all forged, sintered and later pressed steel versions that use AEG167 screw in EN8 with heat treated ends. 1/2" wide AF spanner size head nut to fit AEG167

See [link]...

£0.26 exc vat

£0.31 inc vat

ROCKER COVER T BARS WITH CHROME FITTINGS

SAC71C

Originally marketed by Minispares in the mid 70s so many companies copied them because of their smart looks and ease of fitment. These have been improved by offsetting the arms to help tighten plus stop the arm falling out when they were straight. Ki...

£14.06 exc vat

£16.87 inc vat

ROCKER COVER T BARS RED KIT