£1,424.57 exc vat
£1,709.48 inc vat
In stock
£1,424.57 exc vat
£1,709.48 inc vat
In stockRecommended usage 1 x C-STN23 to fit one mini.
From 1990 1275 carb cooper fitted with HIF44 and non cooper fitted with HIF38 carb. Also use when fitting metro type carb. This is the right hand drive version except for injection cars.
For LHD use SBB10126 (2.5" shorter)
The screw that holds the breather on the clutch case housing and is UNC thread 5/16" bolt and 3/4"long--also used on block for petrol pump
Spacer with gaskets fitted for any 4 bolt fitting carb such as HS6 HIF range about 9/16" (14.5mm). As this is the only thick spacer you need to check stud length.
Emission hose from carb to breather valve, this hose has special size ends and made of a material to cope with taking these emission gases.
Approx 23.75" long with internal 5/16" end and 1/2" other end.
GHC406 jubilee c...
Probably the most changed stud on the mini. This is the length used on every A series engine until the introduction of the sandwich plate when longer ones were required. A stainless steel variety C-STR286 is available which we do recomme...
This plug fits our inlet manifolds and Rover types with servo take off holes..
5/8 UNF grub screw that use 8mm allen key for blanking inlet servo take off or temp transmitter hole at front of pre 1996 cylinder heads. Can also use ADP210
Thin plastic pipe with rubber connectors either end. This replaces the old metal type which also had a vacuum chamber built into the line, that was made obsolete. This hose is 26"(660mm)long and has 2 rubber ends, one straight and one at a right angl...
If you have fitted our inlet and exhaust manifolds plus an RC40 exhaust to a stadard 1275cc engine this needle in a HIF44 carb will work great if coupled with a K&N pancake filter.
Clip on the heater valve for heater cables on vehicles from 1990 where the in line remote heater valve was used. It has also been used as a clip for HIF carbs to hold the cable but the one from Rover is 13H3472.
Special reinforced gasket for injection cars has metal inserts on exhaust ports plus a metal back on the manifold side which makes surface easier to clean when replacing. Often used on Turbo cars when correct gasket is in short supply.
...
Pipercross KK150 chrome top, low-conical, foam air filter for 1.75" SU carb.
Full flow, high capacity competition foam air filters; the KK range of Pipercross high performance air filters offer the ultimate in engine filtration, and are...
Fuel or water T piece adaptor
used when upgrading fuel system size on specials from 1/4" to 5/16" or any other modifications
THIS CARB IS A GREAT TUNING AID ON TUNED ENGINES, ESPECIALLY 1380cc.
For 1275cc engines after 1990 on with HIF38 carbs.
has a 5/16" (8mm)inlet which makes it unique to this model
The 1990-1 models of the Mini with 1275cc engines and HIF44 carbs use a AZX1817 mechanical fuel pump. Driven ...
Electronic Ignition distributor, fitted as standard to all 1300 Carb Cooper models. Also Metro 1275cc engine.
Replacement service items for this are:
Cap GDC156
Rotor arm GRA2143
Should be used with GC...
Main wiring loom less dim dip for mainly overseas cars. Fits all 1275 cars with HIF38 carb from 1991-1994. Ignore alarm wires on early cars.
Main and dash loom only.
Blanking plug to blank of the Lambda sensor hole on all SPI/MPI models.
Rear loom for 1992 on carburettor cars with a 13 way Econoseal plug.
Non Genuine, fits saloons from 1974 until the introduction of injection.
First fitted to 1275GT in 1974 with 12"wheels and all mini saloons from 1980 on
7.5 gallons or 34 litres capacity and the tank is retained by the single stra...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.