TWIN HS4 CARBURETTORS SU PAIR (1.5")

Pair of new 1.5" SUs, with rod linkage, but no heatshield, fuelpipe or manifold; just what you want if you've got a pair of old tired carbs. You will need a 12H889 T piece or 12G292 link pipe to run the fuel system if your o...

£1,006.76 exc vat

£1,208.11 inc vat

TWIN HS4 CARBURETTORS SU PAIR (1.5")

C-AUD640

Pair of new 1.5" SUs, with rod linkage, but no heatshield, fuelpipe or manifold; just what you want if you've got a pair of old tired carbs. You will need a 12H889 T piece or 12G292 link pipe to run the fuel system if your o...

£1,006.76 exc vat

£1,208.11 inc vat

LINKAGE ROD FOR TWIN CARB LINKAGE

AUC1457

Rod with chamfered ends about 57.2mm long(shorten to 54mm for twin HS4) which has AUE586 and AUE587 clamps on to fit between SU twin carbs for the linkage. Quantity of One is usually required per set up plus a 12A31...

£2.15 exc vat

£2.58 inc vat

MANIFOLD TWIN INLET HS4/6

C-AEG489

Cast alloy type, Fits either twin HS4 or HS6.(requires modifacation to fit HS6.2 extra studs per carb)

This intake manifold for twin SUs has been carefully produced to minimize cross-port-flow interference caused by t...

£73.60 exc vat

£88.32 inc vat

MANIFOLD ADAPTOR 1.5"

MFA338

New Carb Spacer for HS4 carbs with vacuum take off. 7.5mm thick.

£16.43 exc vat

£19.72 inc vat

TWIN CARB BUTTERFLY LINKAGE

12A310

The rod with the plate is called the butterfly rod and was fitted to all Cooper twin carb HS2 set ups.

£7.50 exc vat

£9.00 inc vat

THROTTLE BRACKET ON MANIFOLD FOR TWIN CARBS

AEG349

Accelerator bracket for twin carb models, mounts to inlet manifold.

£5.47 exc vat

£6.56 inc vat

2.5" BRAIDED PETROL PIPE 1/4" BORE

PPK1

Before the days of Aeroquip, Minis were fitted with braided steel rubber fuel lines. They should be used in place of rubber for all fuel lines in the engine compartment. They come made to length, with rubber end caps.

If you need the 5/16...

£2.17 exc vat

£2.60 inc vat

TWIN CARB SPINDLE LEVER LH

AUE587

This is the left hand linkage lever that sits on the rods between HS type twin carbs.sold individually

£1.87 exc vat

£2.24 inc vat

WASHER PLAIN 1/4" x 1/2"

GFK1113

£0.08 exc vat

£0.10 inc vat

GASKET 1.5" CARB TO MANIFOLD

AEC2083

Gasket for an HS4-carb and manifold .Sold seperately and order as required for your car(usually 3).

£0.56 exc vat

£0.67 inc vat

CARBURETTOR LEVER PIN

ACC5062

Pin to hold the accelerator cable which locates in the carb bracket lever. Supplied as originally fitted with washers, nut and split pin plus a proper machined hole for the cable unlike many others on the market- which come either bare or with wrong ...

£2.93 exc vat

£3.52 inc vat

PIPE TWIN SU CARB TO CARB

12G292

original shape of petrol feed pipe for twin HS" carbs as fitted to all the Coopers

£9.44 exc vat

£11.33 inc vat

HEAT SHIELD BLACK KIT HS4 TWIN CARBS

MSSK1004

Pair of heatshield brackets and cross bar

these are made similar to the original cooper HS2 design but ARE for HS4 (1.5")carbs and include the 3 correct springs that attach to the bridging bar for choke return linka...

£29.27 exc vat

£35.12 inc vat

TWIN CARB SPINDLE LEVER RH

AUE586

This is the right hand linkage lever taht sits on the rods between HS type twin carbs. Sold individually

£1.87 exc vat

£2.24 inc vat

NUT PLAIN 5/16" UNF

GFK3212

Zinc plated 5/16" UNF plain nut

£0.09 exc vat

£0.11 inc vat

STUD FOR THERMOSTAT HOUSING WITHOUT SANDWICH PLATE...

CHS2515

Probably the most changed stud on the mini. This is the length used on every A series engine until the introduction of the sandwich plate when longer ones were required. A stainless steel variety C-STR286 is available which we do recomme...

£0.65 exc vat

£0.78 inc vat

NUT PLAIN 1/4" UNF

GFK3211

£0.07 exc vat

£0.08 inc vat

THROTTLE RETURN SPRING FOR TWIN CARBS

AEC2075

Throttle return springs for all twin carb variants. Usually 3 fitted.

£1.28 exc vat

£1.54 inc vat

TWIN HS2 CARBURETTOR KIT - LESS A/C

FZX3052

Not built up-A matching pair of HS2 twin carbs with polished dashpot covers plus original type twin HS2 linkage kit, inlet manifold but less air cleaners etc.

The UNC bolt holding the abutment bracket on the inlet m...

£1,146.05 exc vat

£1,375.26 inc vat

HOSE CLIP 8-12MM

GHC108012

Small hose clip for 1/4" fuel line (our part number PETROLPIPE)

£1.16 exc vat

£1.39 inc vat

T PIECE 5/16"

MTP002

Fuel or water T piece adaptor

used when upgrading fuel system size on specials from 1/4" to 5/16" or any other modifications

£4.28 exc vat

£5.14 inc vat

CARB BALANCER TOOL

MSA1003

This tool/gadget allows you to balance both air intakes on either twin SU or twin choke carbs so they flow exactly the same to give better performance and economy.

£28.50 exc vat

£34.20 inc vat

HS4 DASHPOT COVER - BLUE

R23BLUE

brighten up your engine bay area with these bright alloy carb covers --these fit HS2 1.25" type carbs only- see R22 for chrome look and R22RED

£12.89 exc vat

£15.47 inc vat

PETROL PIPE HOSE 1 METRE

PETROLPIPE

Special rubber hose 1/4" bore for use on petrol lines, this is in black and not armour plated outside but does have internal reinforcing. Supplied as pre cut 1m length with 2 clips and is safe to use with modern fuels with higher ethanol content. SAE...

£3.27 exc vat

£3.92 inc vat

15" BRAIDED PETROL PIPE 1/4" BORE

PPK6

Before the days of Aeroquip, Minis were fitted with braided steel rubber fuel lines. They should be used in place of rubber for all fuel lines in the engine compartment. They come made to length, with rubber end caps. 1/4" bore size.

Orange ...

£4.24 exc vat

£5.09 inc vat

ACCELERATOR CABLE NYLON SLEEVED EXTRA LONG

C-AHT85

Our heavy duty throttle cable is superior in many ways.

A nylon interior ensures smooth operation. The outer cable is 32mm longer and inner is 95mm longer than the standard one.

Cable to carb bolt is ACC5062.

£6.10 exc vat

£7.32 inc vat

NEEDLE AAA SWINGING TYPE

CUD1000

A very usefull tuning needle for single and twin carbs when camshaft change for carbs with floating needles.

£8.25 exc vat

£9.90 inc vat

NEEDLE AAV SWINGING

CUD1019

£8.25 exc vat

£9.90 inc vat

NEEDLE AAM SWINGING - STAGE ONE 1275cc 1.5" CARB

CUD1011

£8.25 exc vat

£9.90 inc vat

CARB DASHPOT OIL FOR SU RANGE

BDR125

Correct and original thickness oil for SU carb dashpots.

£7.43 exc vat

£8.92 inc vat

CARB SPRING (RED 4.5oz) HS TYPE CARBS

AUC4387

Standard spring for all HS2 and HS4 on minis except for the 997/998 Cooper from 1964-9 and H4 special tuning carbs which used AUC4587.

£7.59 exc vat

£9.11 inc vat

HEAT SHIELD STAINLESS STEEL KIT HS4 TWIN CARBS

MSSK1006

Stainless steel twin HS4 heatshields kit. Comes with Link bar and springs.

£30.71 exc vat

£36.85 inc vat

NEEDLE AAU SWINGING - STAGE ONE USE

CUD1018

The favourite and best needle for Minispares stage one kit. Tested on a rolling road by Peter Baldwin this baby gave the best performance when using our RC40 system, Minispares inlet and exhaust manifold plus a K&N filter.

If us...

£8.25 exc vat

£9.90 inc vat

CHOKE CABLE TRUNNION ACH9042 NIPPLE & 53K3503 SCRE...

AUE34

Complete with screw the choke trunnion is used on nearly all SU carb linkages.

See ACC5062 for carb cable link trunnion also.

£2.03 exc vat

£2.44 inc vat

BUTTERFLY SCREW

AUC1358

These screws fit all HS type carb butterflies to hold them on the throttle spindle

£0.90 exc vat

£1.08 inc vat

"T" PIECE 1/4" SU TWINS MTP001

12H889

Used in petrol fuel lines to take 1/4" petrol hoses it is used mainly on twin carb set ups for petrol being diverted to the 2 carbs.

£4.50 exc vat

£5.40 inc vat

MANIFOLD LOCATING RING

12G297

Locating rings originally made for 12G295 heads with twin carbs to line up the inlet manifold to the inlet ports on the cylinder head it found its way on most twin carb factory produced cars. There is a recess in the inlet port on the he...

£2.56 exc vat

£3.07 inc vat