ROCKER ADJUSTING NUT 1/2" AF NUT SIZE
NT605061

£0.26 exc vat

£0.31 inc vat

In stockIn stock
The larger 5/16 unf size rocker screw as used on all forged, sintered and later pressed steel versions that use AEG167 screw in EN8 with heat treated ends. 1/2" wide AF spanner size head nut to fit AEG167

See AEG167EVO upgraded hex head type.

Rover EN1a std Budget screw is 12H3376.

Also stocked are performance nut C-AHT449 and C-AHT450

£0.26 exc vat

£0.31 inc vat

In stockIn stock

Recommended usage 8 x NT605061 to fit one mini.
Cylinder Head 850CC, 998CC & 1100CC Pre 'A' Plus - Qty 8
997CC & 998CC Cooper Cylinder Head - Qty 8
Cylinder Head, 998CC, 'A' Plus 1980 on - Qty 8
Cylinder Head Cooper 'S' 970CC, 1071CC & 1275CC - Qty 8
1275 Except Cooper 'S' & Turbo - Qty 8
Cylinder Head 1275 Turbo & Heads with Triple Coll - Qty 8
Cylinder Head - Qty 8

Alternative products

Mini Spares genuine upgraded part. Hexagon head rocker screw nut in EN24T.

Also available is a flanged nut C-AHT449

Kit products

Roller-tip rocker assembly with black post 1.5 Hi-Lift for 1275cc big bore engines only.

Ensure you tighten down all posts equally to eliminate stress fractures on shaft

To use on small bore heads it is necessary to re-arrange the ...

standard lift 1.3 roller tipped rockers for 1275cc engines only

Roller-tip rocker assembly. 1.5 Hi-Lift for 1275cc 8 port cylinder heads only.

this kit has 6 L/H rockers and 2 R/H. Specially designed to fit the currecnt July 2012 on head, with corrected geometry to give more stability over the valve and...

Hi-Lift forged rockers on our special rocker shaft with AEG167 adjuster screws for road or race.

Ensure posts are equally tightened down to eliminate stress fractures on shaft.

Using 1.5 ratio high lift rockers has alm...

This set of roller tip rockers is standard lift of 1.3 and does not run on

bronze bushes,also available for 1275cc as C-AHT400

Genuine Mini Spares part- 1.5 Hi Lift Roller-tip rocker assembly for 1275cc with gold anodised steel posts.

These extra high-spec alloy Purple rockers were introduced in 1998 to give push rods a better clearance on A Plus heads.

...

People also bought products

Mini Spares genuine upgraded part. Hexagon head rocker screw nut in EN24T.

Also available is a flanged nut C-AHT449

This kit of head studs is the best available for road and lightly tuned engines. See the C-AHT280 set for highly tuned engines.

The material spec is alloy steel heat treated to 75 tensile tons per square foot minimum and finish...

ARP Head stud kit that compromises of;

4 x Long Head Studs

7 x Short Head Studs (Disregard 2 if you're using a 9 stud application)

11 x Multipoint ARP nuts

11 x Heavy Duty Washers

4 x Rocker post studs <...

Complete stud, nut and washer kit for the cylinder head ancillaries. Kit contains parts to retain the following:

Inlet/Exhaust manifold to head, studs/nuts/washers

Thermostat housing (no sandwich plate) studs/nuts/washers

H...

Minispares own stainless steel manifold stud and 6 sided hexagon nut kit.

For mutipopint nut kit see C-STR287

Quantity required one kit per car

Minispares own stainless steel Thermostat housing stud kit for the single tier type thermostat housing.Quantity required one kit per car

This thermostat housing fitting kit, suitable for all single tier thermostat housings. Comes with new studs, nuts, washers and Klinger thermostat housing gasket

Universal stud made for fitting the HS4/HIF carb to the manifold (except HS6 with alloy spacer on cast one piece manifold which requires CHS2515 (5.8mm longer)) and it also fits the cylinder head to take the thermostat housi...

replacements in stainless steel for the heater tap elbow on the cylinder head.

Quantity required one kit per car

Chrome Rocker bolt with UNF thread. Original Rocker cover bolts are dull zinc coated or painted but the chrome type look much better and cheaper.

A longer threaded version CAM6823 was used on prestige Minifin alloy type A series...

This 5/8unf steel hexagonal head blanking plug was made for the inlet manifolds where the servo union can be fitted, plus blanking off the thermal transmitter hole under the thermostat. Uses 1B3664 washer ----------please note this will ...

A simple way to dress up that engine compartment while at the same time insuring all the proper hardware is in place. A kit includes 2 each of British made chrome sleeve nuts, spacers and special cup washers, Fits all A & B series engines.

F...

Originally marketed by minispares in the mid 70s so many companies copied them because of their smart looks and ease of fitment they were improved by offsetting the arms to help tighten plus stop the arm falling out when they were straight. These T b...

Originally marketed by Minispares in the mid 70s so many companies copied them because of their smart looks and ease of fitment. These have been improved by offsetting the arms to help tighten plus stop the arm falling out when they were straight. Ki...

Manifold stud 39mm long for all A series engines up to injection which use LYR10028 which is 6mm longer at 45mm.

Special extra long nuts were used on some manifolds. These nuts are about an inch long for easy reach and made of brass so they'll never corrode. Especially handy on the inner two studs on dual carb set-ups.

Sold singly and usually 2 used f...

This kit of head studs is the best available for road and lightly tuned engines. See the C-AHT280 set for highly tuned engines.

The material spec is alloy steel heat treated to 75 tensile tons per square foot minimum and finish...

Probably the most changed stud on the mini. This is the length used on every A series engine until the introduction of the sandwich plate when longer ones were required. A stainless steel variety C-STR286 is available which we do recomme...