(1 656,53 €) £1 656.53 exc vat
(1 987,84 €) £1 987.84 inc vat
In stock
MPI twin point injection only half engine with MDM274MPI camshaft which is as far as you can go for further power without other modifications. A gas flowed head MSE7 or alternative would also work well with this set up.
£500 surcharge on old unit.
(1 656,53 €) £1 656.53 exc vat
(1 987,84 €) £1 987.84 inc vat
In stockRecommended usage 1 x ENG008 to fit one mini.
Brand new - last from the factory, built half engine (block, crank, rods and pistons only) for MPi cars. Does not have the expensive camshaft fitted.
If you have an MPi, these are a good investment at less than half the original retail price...
The "slot" drive oil pump has been the factory standard for many years. The evolution of the pump in production was started with the "pin" drive that is most common in early small bore motors. These pumps have a fork on the drive side to engage the "...
Brass type core plug for engine. Originally, engines had brass oilway plugs (2K1345) 1/4" hole fitted. These cup type plugs replaced them about 1985. 12.7mm cup type plug about 9.6mm deep. Fits 1/2" hole.
All good engine tuners ...
Cup type core plug for all A plus and 1275cc engines except for Cooper S. 33.6mm wide.A plus 5 required but only 4 on 998 A plus. 1275 has 2 core plugs oil pump end of block whereas 998 only has one
Good maintenance, just as you would never rebuild your motor without replacing the crank thrust washers, you should also care about the camshaft thrust plate. Sometimes called the "triangle plate" this small but important plate doesn't just hold the ...
Standard cast duplex gear set from the original AE supplier. for road use only.
Found to be the best fitting in Mini Mag feature Autumn 2007.
Driving the cam and controlling the timing relationships between the cam and the crank i...
Original equipment quality for factory built engines giving longer life expectancy on road cars under variable conditions of oil and use. These are the 1275cc mains as fitted to A Plus engines with the locating tab in the middle rather than to the ou...
Big end shell bearings for the 1275 larger 1.75" diameter rod pin-not Cooper S
( Tri-Metal )
Sintered copper lead, lead plated,steel backed
Nominal Composition
Copper 74%
Lead 24%
Tin ...
Set of 8, original leyland ST product but now made for us to our specification. Critical to the life and performance of the camshaft is the use of high quality cam followers. Remember, they operate in a finite hole and thus the dimensional tolerances...
Low drag 1275 piston standard size 2.780 plus 20 thou oversize(Rings included).
This piston has a possible compression ratio of 10.3:1 as fitted to Cooper RSP 1990.
The best performance 1275 pistons are C-STN100 range which have 9.7...
The only upgrade in camshaft you can get away with on the multi point injection cars without changing ECU etc--A mild road cam.
As of July 2007 Kent cams have no supply of old camshafts for reprofiling and we will only supply camshafts fro...
SET OF STANDARD SIZE 1275 CRANK THRUST WASHERS
This kit of head studs is the best available for road and lightly tuned engines. See the C-AHT280 set for highly tuned engines.
The material spec is alloy steel heat treated to 75 tensile tons per square foot minimum and finish...
ESPECIALLY FOR MINIS
This 20-50w semi synthetic oil is produced especially for minis where it needs to lubricate both engine and gearbox parts giving the neccessary coating and protection. Semi synthetic has a long life to 100c with maximum ...
Genuine Mini Spares Performance Copper/steel head gasket.
Based on the original AF460 pre 2000 design plus the old Payen Special tuning C-AHT188 with superior sealing rings.
With modern day technology and NON asbestos l...
Converted into a non melting type grease.Favoured by proffessionals for camshaft,lobes and lifter,and any valvetrain to stop scuffing on start up. Also useful for oil pumps to stop drain back on start up
PRIMARY GEAR C WASHER 0.125" thick average.
It is better to use a new item if you are running a performance engine and you wish to shim the primary gear up perfectly. This fits against the 88G549 spacer backing ring.
Ou...
Mini Spares spacer kit re-designed in 2005 for correcting rocker alignment.
This kit has been produced to help rocker pad and valve stem alignment plus reducing friction. The standard springs can be replaced with this special kit of 3 spacer...
Only a few parts in this kit but thats all you need for the twinpoint engine headset with the latest head gasket and correct manifold gasket.
Genuine Mini Spares best selling super upgraded Klinger gasket set for any popular engine block.
So called genuine Rover gasket sets were so poor in quality or have incorrect parts we decided to put together our own correct real gasket set u...
0.6875"HOLE. Earlier engines pre A plus use 12A398 locktab.
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.