(39,74 €) £39.74 exc vat
(47,69 €) £47.69 inc vat
In stock
(39,74 €) £39.74 exc vat
(47,69 €) £47.69 inc vat
In stockRecommended usage 1 x SEN45 to fit one mini.
Set of 4 hoses, 2 front and 2 rear.
Braided brake and clutch hoses have a PTFE inner which helps to eliminate the spongy pedal feel under arduous conditions, and give greater efficiency. The outer braided stainless steel cover e...
Seal for between the brake servo and master cylinder, fits all late 1988 onwards vehicles where the master cylinder was mounted directly to the servo unit.
Set of 6 hoses, 4 front and 2 rear to fit the ERA turbo.
Braided brake and clutch hoses have a PTFE inner which helps to eliminate the spongy pedal feel under arduous conditions, and give greater efficiency. The outer braided st...
Replacement rubber grommet for the servo vacuum hose for the 1992 onwards brake servo (GSM119)
NICKEL copper easy bend brake pipe with 2 metric male unions. 22"long, for 1988 on master cylinder lower outlet to PDWA valve outlet nearest to wing-other pipe is HMK026-both for left or right hand drive.
These pipes are retail...
We now supply 2 easy bend copper nickel pipes with the correct unions for when converting to the later type GMC227 front to rear split master cylinder.
Brake pipe with male metric ends, 12mm for master cylinder and 10mm for PDWA valve. fits in the bottom union and goes to left hand union in valve (to go to rear brakes)
As the original brake pipe kit is now obsolete, we now supply 2 easy bend copper nickel pipes with the correct unions for when converting to the later type GMC227 front to rear split master cylinder.
Cooper S 7.5" complete brake disc kit, except for disc shields, with Mini Spares own cast standard calipers. If you want or have 10" wheels this is the kit to convert from drum brakes to discs brakes.
This kit includes every nut bolt and co...
Brake pipe connecting piece originally used on diagonal split system.1.25" long
Single line L/H/D with servo-dry suspension. If you have a drum brake mini then this kit will require 2 front wheel cylinder to wheel cylinder pipes HF10
Adjustable original brake proportioning/balancing valve for racers only.
The most common brake system on the Mini has Disc brakes in the front and drums in the rear. The weight bias on the car is all in the front and thus under hard braking...
Pair of vented discs and Mintex GBP258AF pads,one of our best selling brake disc kits. Includes discs[link](GBD496)/link] which are a bargain.Only for carss fitted with vented discs already.
This is not a direct replacement kit ...
Pair of 4-pot alloy calipers for 8.4" diameter brake discs with 12" (or bigger) wheels. Kit includes pad pins, but not brake pads.
The advantage of alloy calipers is that they dissipate heat quicker, reducing fluid boiling. The design a...
Easy bend copper 12" brake pipe with 2 male ends for single line master cylinders---for clutch or brake on early minis but the longer HF14 might be easier for the brake master which was nearer 13" long. These kits or pipes are at least 3...
Front to rear brake pipe, 101" in length. Includes male fittings on each end. Some early dry cars used a 103" pipe.
Easy bend copper brake pipe 26" long with one female and one male end - used on hydrolastic cars from regulator valve to near side rear hose. These pipes are retail less 35% discount at least to keep prices viable.
Front to rear brake line kit for cars from 1988-2000 with the factory Servo incorporated into the brake master cylinder. You'd think that the way Minis leak oil they'd never rust on the underside, but they do! If your Mini is rusty below it is a good...
Special formulated hose for brake servos and engine emmission breathers sold in a 22 inch length. 3/8" inner bore.
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.