ROCKER SHAFT WASHER 40 THOU WIDE
AEG168

£0.23 exc vat

£0.28 inc vat

In stockIn stock
Originally fitted to help rocker pad to valve stem alignment and reduce friction, the standard springs can also be replaced with solid spacers and these shims. The spacers including correct shim set are sold as a set C-AEG392[.

Sold individually.

£0.23 exc vat

£0.28 inc vat

In stockIn stock

Recommended usage 4 x AEG168 to fit one mini.
Cylinder Head Cooper 'S' 970CC, 1071CC & 1275CC - Qty 1
1275 Except Cooper 'S' & Turbo - Qty A/R
Cylinder Head 1275 Turbo & Heads with Triple Coll - Qty 1

Alternative products

Sold individually.

To help rocker pad to valve stem alignment and reduce friction, the standard springs can be replaced with solid spacers and correctb shim set. The spacers and shim kit are sold as C-AEG392.

Kit products

Mini Spares spacer kit re-designed in 2005 for correcting rocker alignment.

This kit has been produced to help rocker pad and valve stem alignment plus reducing friction. The standard springs can be replaced with this special kit of 3 spacer...

People also bought products

Mini Spares genuine upgraded part. Hexagon head rocker screw nut in EN24T.

Also available is a flanged nut C-AHT449

Replacement Rocker arm adjusting screw as fitted to 1275 engines with sintered type rockers and for use on any 5/16 thread type.

Use better EN8 quality AEG167 or race type AEG167EVO.

Will fit the forged S r...

Sold individually.

To help rocker pad to valve stem alignment and reduce friction, the standard springs can be replaced with solid spacers and correctb shim set. The spacers and shim kit are sold as C-AEG392.

Direct replacement rocker shaft. Fits all except full needle roller types. Far superior to the stock item! ENSURE YOU ALWAYS TIGHTEN DOWN ALL POSTS EQUALLY to eliminate stress fractures on shaft.



Our special "heavy duty" shaft has ...

Rocker shafts wear fairly quickly. The upside to this used to be that the rocker bushes lasted longer, but later sintered rockers run without bushes. It is easier and less expensive to replace the rocker shaft!

Fits all models but beware as ...

Genuine Mini Spares upgraded UK made EN8 screws, specially heat treated in correct places as per original drawings, sold individually without nuts.

Nuts are sold individually as NT605061.

Used on our 1.5 forged and roll...

This is the nut for the early 12A1215 rocker adjusting screw with 7/16"af spanner size and Not a UNF thread. For the later 1/2" spanner size see AEG167 screw and NT605061 UNF nut.

Sold singly,8 required...

Sold individually.

Even if you regularly replace the rocker shaft, the rocker bushes will eventually wear.

Fits all but the latest rockers.

Individual forged rocker arms, for C-AHT436 assembly. Less screw and nut. See AEG167, screw or AEG167EVO and NT605061 nut.



These cannot be used with standard rocker posts

The only current production rocker from Rover is sintered and runs without a bush and was first used from 1974 on. A fairly inexpensive replacement. See AEG167 and NT605061 for the adjusting screw and nut.

Victor Reinz large bore head gasket for A-series engines.

Victor Reinz/Mahle small bore head gasket for A-series engines.



Gasket fitment. Writing side up.

New competition valve cotter for early heads with the large single groove valve, these are precision CNC machined from 4340 and heat treated to a better spec than EN24T and claimed to be stronger in fatigue life.

These locate better in the v...

Spring seat shims (set of 4), 0.020" thick (0.5mm).

Spacer shims to increase valve seat pressure and overall spring rate.

These were also used on all the 8 port head valve seats to prtect the alloy seats from wear. (8 port now C-AHT...

Spring seat shims (set of 4), 0.040" thick (1mm).

Spacer shims to increase valve seat pressure and overall spring rate.

These were also used on all the 8 port head valve seats to prtect the alloy seats from wear. (8 port now C-AHT36...

Fitting kit comprising of studs, nuts, plain washers, spring washers and a gasket

This kit of head studs is the best available for road and lightly tuned engines. See the C-AHT280 set for highly tuned engines.

The material spec is alloy steel heat treated to 75 tensile tons per square foot minimum and finish...

ARP Head stud kit that compromises of;

4 x Long Head Studs

7 x Short Head Studs (Disregard 2 if you're using a 9 stud application)

11 x Multipoint ARP nuts

11 x Heavy Duty Washers

4 x Rocker post studs <...

New competition valve cotter, these are precision CNC machined from 4340 and heat treated to a better spec than EN24T and claimed to be stronger in fatigue life.

These locate better in the valves and easier to control spring heights.

Upgraded rocker cover gasket made in silicon, cut outs for 11 stud head and ideal when rocker cover is removed on a regular basis.

Rarely you may require longer rocker cover bolts when fitting this so use CAM6823.