ROCKER SHAFT HEAVY DUTY
C-AEG399

£24.00 exc vat

£28.80 inc vat

In stockIn stock
Direct replacement rocker shaft. Fits all except full needle roller types. Far superior to the stock item! ENSURE YOU ALWAYS TIGHTEN DOWN ALL POSTS EQUALLY to eliminate stress fractures on shaft.



Our special "heavy duty" shaft has a super accurate finish but it is also has an increased wall thickness to approx 3.7mm. This means that although the shaft is totally interchangeable with the original stock version, it is a significant upgrade! The locating plug is in the second post which stopped flex and wear. If you have the original shaft with the locator in the first post you will need to move the post along but get another post to ensure the oil feed to the rockers through the head is not blocked. GFK102 split pins fit the ends to hold all the rockers and posts on--Spacers are AEG168 and AEG169

£24.00 exc vat

£28.80 inc vat

In stockIn stock

Recommended usage 1 x C-AEG399 to fit one mini.
Cylinder Head, 998CC, 'A' Plus 1980 on - Qty 1
Cylinder Head Cooper 'S' 970CC, 1071CC & 1275CC - Qty 1
Cylinder Head 1275 Turbo & Heads with Triple Coll - Qty 1
Cylinder Head - Qty 1

Recommended products

original rocker shaft spring (3) between rockers on every A series engine

Number 1,3&4 rocker posts. There are 3 of these on your rocker gear all with oil holes although the cylinder head has only one outlet and the single 12G1927 post has the rocker shaft locking plug hole. Some very early cars had the lockin...

The standard end washer for the rocker shaft but see AEG168 and AEG169 for spacer shims or complete kit C-AEG392

There is one of these on the rocker gear with locking plug hole for Post No 2.

The other three 12G1926 have the oil holes although the cylinder head has only one oil hole outlet on number one post. Some very early cars had the l...

Originally fitted to help rocker pad to valve stem alignment and reduce friction, the standard springs can also be replaced with solid spacers and these shims. The spacers including correct shim set are sold as a set C-AEG392[.

...

Spacers for under the rocker pedestals are used mainly by engine tuners to allow tappet adjustment to be made where cylinder head mods have been carried out. 1.3mm/0.0512" thick, this can be used to hold locating screw on rocker post assembly but the...

Sold individually.

To help rocker pad to valve stem alignment and reduce friction, the standard springs can be replaced with solid spacers and correctb shim set. The spacers and shim kit are sold as C-AEG392.

Universal split pin for all mini clevis pins, except handbrake lever.

Split pin for common clevis pin list

GFK101 for CLZ409 handbrake levers to cable on rear drum

GFK102 most mini cle...

Alternative products

Rocker shafts wear fairly quickly. The upside to this used to be that the rocker bushes lasted longer, but later sintered rockers run without bushes. It is easier and less expensive to replace the rocker shaft!

Fits all models but beware as ...

Kit products

Roller-tip rocker assembly. 1.5 Hi-Lift for 1275cc 8 port cylinder heads only.

this kit has 6 L/H rockers and 2 R/H. Specially designed to fit the currecnt July 2012 on head, with corrected geometry to give more stability over the valve and...

Hi-Lift forged rockers on our special rocker shaft with AEG167 adjuster screws for road or race.

Ensure posts are equally tightened down to eliminate stress fractures on shaft.

Using 1.5 ratio high lift rockers has alm...

Genuine Mini Spares part- 1.5 Hi Lift Roller-tip rocker assembly for 1275cc with gold anodised steel posts.

These extra high-spec alloy Purple rockers were introduced in 1998 to give push rods a better clearance on A Plus heads.

...

People also bought products

Mini Spares genuine upgraded part. Hexagon head rocker screw nut in EN24T.

Also available is a flanged nut C-AHT449

Replacement Rocker arm adjusting screw as fitted to 1275 engines with sintered type rockers and for use on any 5/16 thread type.

Use better EN8 quality AEG167 or race type AEG167EVO.

Will fit the forged S r...

Sold individually.

To help rocker pad to valve stem alignment and reduce friction, the standard springs can be replaced with solid spacers and correctb shim set. The spacers and shim kit are sold as C-AEG392.

Originally fitted to help rocker pad to valve stem alignment and reduce friction, the standard springs can also be replaced with solid spacers and these shims. The spacers including correct shim set are sold as a set C-AEG392[.

...

Rocker shafts wear fairly quickly. The upside to this used to be that the rocker bushes lasted longer, but later sintered rockers run without bushes. It is easier and less expensive to replace the rocker shaft!

Fits all models but beware as ...

Genuine Mini Spares upgraded UK made EN8 screws, specially heat treated in correct places as per original drawings, sold individually without nuts.

Nuts are sold individually as NT605061.

Used on our 1.5 forged and roll...

This is the nut for the early 12A1215 rocker adjusting screw with 7/16"af spanner size and Not a UNF thread. For the later 1/2" spanner size see AEG167 screw and NT605061 UNF nut.

Sold singly,8 required...

Sold individually.

Even if you regularly replace the rocker shaft, the rocker bushes will eventually wear.

Fits all but the latest rockers.

Individual forged rocker arms, for C-AHT436 assembly. Less screw and nut. See AEG167, screw or AEG167EVO and NT605061 nut.



These cannot be used with standard rocker posts

The only current production rocker from Rover is sintered and runs without a bush and was first used from 1974 on. A fairly inexpensive replacement. See AEG167 and NT605061 for the adjusting screw and nut.

Victor Reinz large bore head gasket for A-series engines.

Victor Reinz/Mahle small bore head gasket for A-series engines.



Gasket fitment. Writing side up.

New competition valve cotter for early heads with the large single groove valve, these are precision CNC machined from 4340 and heat treated to a better spec than EN24T and claimed to be stronger in fatigue life.

These locate better in the v...

Spring seat shims (set of 4), 0.020" thick (0.5mm).

Spacer shims to increase valve seat pressure and overall spring rate.

These were also used on all the 8 port head valve seats to prtect the alloy seats from wear. (8 port now C-AHT...

Spring seat shims (set of 4), 0.040" thick (1mm).

Spacer shims to increase valve seat pressure and overall spring rate.

These were also used on all the 8 port head valve seats to prtect the alloy seats from wear. (8 port now C-AHT36...

Fitting kit comprising of studs, nuts, plain washers, spring washers and a gasket

This kit of head studs is the best available for road and lightly tuned engines. See the C-AHT280 set for highly tuned engines.

The material spec is alloy steel heat treated to 75 tensile tons per square foot minimum and finish...

ARP Head stud kit that compromises of;

4 x Long Head Studs

7 x Short Head Studs (Disregard 2 if you're using a 9 stud application)

11 x Multipoint ARP nuts

11 x Heavy Duty Washers

4 x Rocker post studs <...

New competition valve cotter, these are precision CNC machined from 4340 and heat treated to a better spec than EN24T and claimed to be stronger in fatigue life.

These locate better in the valves and easier to control spring heights.

Upgraded rocker cover gasket made in silicon, cut outs for 11 stud head and ideal when rocker cover is removed on a regular basis.

Rarely you may require longer rocker cover bolts when fitting this so use CAM6823.