FLYWHEEL LIGHTWEIGHT STEEL ROAD/RALLY INERTIA STAR...
C-AEG421

£147.32 exc vat

£176.78 inc vat

In stockIn stock
Light Weight STEEL flywheel (4.48kg - 9.88lbs). For non-Verto clutch and non-pre-engaged starter.

see C-AEG420 for pre-engaged starter type.

"1 lb off the flywheel is like taking 100 lbs off the car." Not quite rational but close. This rule of thumb indicates the importance of flywheel performance. The stock cast iron 1275 flywheel is almost 22 lbs. Even the "S" flywheel weighs almost 17lbs. The stock flywheel is "cast" iron and thus not very safe to lighten.

This new "Road" Steel one piece flywheel is 11 lbs and provides tremendous improvement in acceration. (The full race version C-AEG619 is 8lbs.)

Special Tuning originally produced this flywheel and it was even fitted to Allegros by Leyland to stop clutch judder under warranty claims.

Effects of lightening rotating engine components:

(0.5 x n2 x r2 + R2) / R2

n = total gear ratio (gear ratio x diff ratio)

r = radius of gyration

R = Radius of wheel/tire

This formula gives what accelerative weight the engine sees of the car per lb.

Radius of gyration of a transverse engine's flywheel is approx. 3.75"

So to determine "weight loss" for a flywheel weight of say 18 lb to 10 lb,

the engine would see an overall weight loss of the car to accelerate in first gear of:

3.33 = 1st gear of 4 synchro 'S' box

3.44 = diff ratio

(0.5 x (3.33 x 3.34)2 x 3.752 + 9.52) / 9.52

= (0.5 x 131.2 x 14.06 + 90.25) / 90.25

= 1012.59 / 90.25 = 11.22 lbs

So for every 1 lb removed from the flywheel, the engine sees 11.22 lbs less

to accelerate off of the total car.

Therefore by lightening the flywheel by 8 lb,

the engine sees a total reduction of the cars accelerative weight of 89.68 lb.

£147.32 exc vat

£176.78 inc vat

In stockIn stock

Recommended usage 1 x C-AEG421 to fit one mini.
Diaphragm Clutch & Slave Cylinder - 1964 ON - Qty 1

Alternative products

Ultra light (3.87kg - 8.53lbs) EN8 steel billet race flywheel for diaphragm clutch {NOT-Verto} with ring gear for non-pre-engaged starter

.Forged is more rigid at high speed.

The latest refinement of the Ultra-light Mini flywheel is...

Kit contained products

The thin ring gear is for old type inertia type starters and used on our steel flywheel C-AEG619 and C-AEG421. Originally fitted to automatic cars and old cast flywheels when lightened by various tuning shops in the 79s and ...

People also bought products

Pre verto flywheel bolt and keyway washer in EN24T



The bolt is CNC machined from stock EN24T steel with extra attention to the radius under the head to maximise strength.

Plate on the end of the PRE A plus long type clutch arm 22A2204MS to hold the return spring 1G5999. The clevis pin to hold this on the arm is CLZ518--this is the square type but for earlier tapered type Rover ar...

Pre verto race quality tuftrided clutch arm kit made in EN24T for any heavy duty diaphragm- special design plunger with arm to suit, hardened clevis pin and R-clip included.

Upgraded Centre boss for all verto clutch/flywheel.

Fixing bolts are DAM5920 which are supplied in many clutch kits.

Race quality bolt-sold seperately- these shorter bolts hold the spring straps 2A3658 to the flywheel on diaphragm type flywheels only. Not for Verto flywheel.

Only tighten up to 16lbs per sq foot torque when using shake proof wa...

Race quality shoulder bolts for the Mini clutch backplate to the diaphragm--sold seperately- heavy duty racing type EN16 tightenn up to 16lbs per sq foot torque when using shake proof washer or 18lbs and locktite. Use with C-2A3659 race ...

Heavy duty clutch release bearing with a wider surface area, helps to spread even pressure on the clutch diaphragm and is favoured by racers.



small face with numbers stamp-face outwards, larger surface aera side face flywheel.

3 piece Verto Clutch kit for Turbo with 180mm plate which can be used on any Verto flywheel including injected cars. Approximately 20% upgrade over standard this is ideal for any tuning mods to any Verto flywheel but cars from 1990 were fitted with a...

Anchor tab for return spring that fits behind bleed valve on Slave cylinders, for Pre Verto clutches.

Upgraded pre verto clutch lever arm plunger. Surely to be copied by competitors as the early diaphragm clutch really needed a quality item to be remade. This is the carrier that holds the clutch release bearing and on the other end has a hole for the...

Performance type Verto 180mm wide paddle type drive plate as used for racing.

Alternative to AP Racing plate

Mini Spares Performance clutch plate.

Great upgrade for increased performance engines,tested to 10,000rpm and to destruction for evaluation.

For diaphragm type clutch, pre verto. Great clutch plate and a better priced alternative t...

Borg and Beck Clutch Plate,upgraded when fitted to ERA Turbo,great plate for lightly tuned cars from 850-1275cc.

Upgrades after this are C-AHT595 which is ideal for any std road use on 1275cc and C-AHT596 from AP r...

Delete the metal pipe and existing hose by fitting this longer one piece steel braided pipe which can be used for either early or verto clutches. A sensible modification for all mini owners.

Clutch diaphragm, blue for 1275/1100/998/850 Mini, pre Verto.

This part superseded the GCC102 850-1100 diaphragm.

The bolt that holds the flywheel to the crank on cars with a diaphragm type clutch. Locked in place by 22A1155 locktab on the 88G508 key washer.

There are 3 of these shorter 5/16"unf bolts holding the spring straps 2A3658 to the flywheel on diaphragm type flywheels only. Not for Verto flywheel.

Only tighten up to 16lbs per sq foot torque when using shake proof washer or ...

Steel Road weight 4.87lbs( 2.211kg) Pressure plate for diaphragm type clutches.

Now same uprated material and design of C-AHT230-

Great alternative and upgrade for the obsolete Cooper S and std mini type backplate for ...

Long Pre Verto clutch arm.

Ensure you adjust the clutch properly otherwise the hydraulics are powerful enough to bend the ball end of the clutch arm, whether it be an old genuine or a new Mini Spares part. Replaces the old thin arm version 2...