£185.17 exc vat
£222.20 inc vat
Out of stock
£185.17 exc vat
£222.20 inc vat
Out of stock
handbrake handle in Burr walnut to compliment the wooden dashes.
The inside is rough finished and depending on year of car tape will have to be
used on the lever to make this a snug fit.
See also MSA0193 door ...
Walnut Burr gear lever knob.
Standing 4 inches tall and carved from billet burr walnut, it really makes a statement. It has a Mini winged logo pattern embossed.
door window winder handle pair in Burr walnut finish to compliment the wooden dashes.
If your old screws do not fit see G285
See also MSA0193 door opening handles, MSA0191 door cappings and MSA0192...
Alloy dash for cars with 2 clock pod in front of driver and L/H/D--these dashes have a knob on the glovebox.
For cars with 3 clock speedo cluster in front of the driver on left hand drive cars this has 3 extra gauge holes cut out.
Lovely Burr walnut dash for left hand drive cars with 3 clocks in front of driver.
Black vinyl dash liners suitable for 2 and 3 clock clubman type dash with the offset clocks (Left hand Drive).Vinyl will need cutting out for vent holes but the cardboard backing is pre cut.
Alloy dash for cars with 2 clock pod in front of driver and L/H/D--these dashes have a knob on the glovebox.
door cappings in carbon fibre to compliment carbon fibre finished dash
Works Dash for LHD cars.
The later type more common dashes as used on the classic works Monte Minis and rally cars from ST Abingdon.
In crackle black finish.
Attaches to top and bottom parcel shelf rails either side...
Chromed version of the standard demist vent on early cars where the ashtray is
mounted in the top and middle of the metal facia. Not for later cars with large
padded windscreen rails and ashtray in the front such as Mini Clubman and...
The black vinyl covering that lays on your lower dash shelf. For cars after 1970 where the facia panel is not a full metal panel you must fit (link)DT3076(/link)
Fitted for safety regulations to all MK2 minis from 1967-80 except Sweden and Canada to 1975 (not any MKI or van and pick up). Later commercial type minis did have it fitted with 3 clock speedo pod. This is a hard foam pad at the lower edge of the pa...
Ashtray that sits in the upper padded dash on all vehicles with 2/3 clocks positioned in front of driver. Early cars had flat plastic tray face whereas later cars had crinkly type face which is the only type available- They all fit the same.
Late type swith carrier with 4 square holes plus heater and choke cable holes-uses the ratchet type choke cable with D shape fitting--earlier cars used round hole for pull and push chooke cableCZH3591
Kit of four plastic carpet protectors for where the seat frame runs. Two are flat and two are shaped to help with the shape of the tunnel. This kit includes the securing rivets. Ideal if your carpet is in good condition but the plastic plates have de...
Reproduction of the original type fireproof bulkhead sound-proofing foam insulation. These often detiriorate overtime and turn into a crumbly mess.
These are pre-cut for the mounting points and accessories that are on the bulkhead...
This woodrim steering wheel requires a centre boss to suit your particular car and is the best value and quality wheel around in its class. Brightwork 3 spoke
centre design.
This set will fit all Travellers and Estates built between 1966 until 1980. The kit contains a piece of carpet to fit the rear of the back seat and another piece to cover the rear floor area. For the earlier 4 piece kit pre 1996 with external tank se...
Mk1 style alloy gear knob. Will suit any Mini standatd gear lever thread.
3 point automatic rear seat belt. These seat belts do not use the standard C post nor the MPI fixing in the rear pocket. They require the fitting of the real on to the parcel shelf. These seat belts will work for all minis up to 1996.
...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.