£11.79 exc vat
£14.15 inc vat
In stock
£11.79 exc vat
£14.15 inc vat
In stockRecommended usage 1 x GBP281 to fit one mini.
Not included with any brake pads these days owing to universal usage these
pins and retainer clips should always be changed when fitting new pads.
For vehicles with 8.4" discs and standard 2 pot calipers,1984 onwards.
Set of 4 Brake pads from the original manufacturer Delphi for the 8.4" wide disc fitted as standard to minis from 1984on with 2.920" pad width.
A set of split pins are available as GBK1010 or with metal retaining clips as [link]...
For use on 8.4" wide standard brake disc calipers, 2.920"wide.
This is the Ultimax upgrade which produces less brake dust which destroys alloy wheels. For the upgraded version of this see C-AHT16GREEN.
A set of split pins are availa...
We are now able to offer the origianl style 1 piece moulded carpets as fitted to 1997-2000 cars, these come supplied with the underlay although it is available separately under part number CK907. You could fit this carpet to any rod change Mini with ...
Rubber gaiter to keep debris from entering the drum via the backplate handbrake lever SMN10005. Sold singly per backplate, 2 required per car.
Genuine AP Lockheed rubber boot
Master Cylinder repair kit for repairing the late GMC90376 master cylinder that was attached to the servo from 1995 until the end of production this kit uses a longer seal in conjunction with a nylon bearing. If your master cylinder has a drill hole ...
For use on 8.4" wide standard brake disc calipers, 2.920"wide.
This is the Ultimax upgrade which produces less brake dust which destroys alloy wheels. For the upgraded version of this see C-AHT16GREEN.
A set of split pins are availa...
Die cast alloy brake drums with built in spacer-imported copy but have proven 100% reliable on sales from 1998 without any problems. The alloy material has a finned design that dissipates heat quicker which in turn helps reduce brake fade. While desi...
Non genuine pair of L/H disc shield covers for the 8.4" disc size. Fitted as standard from 1984 to 2000. Non genuine but all that is available. It comes complete with the little locating bracket. If you require just the bracket, order it separately ...
Almost every Mini built prior to the dual circuit system uses a .70" bore master cylinder. This kit fits them all. The original size in the '59-'64 Mini was .75" but as most of these cylinders have been replaced with the .70" size it is best to check...
Minispares own product-L/H, to last Rover drawings and supplied to us by a UK Heritage specialist. Originally the BMC castings were machined by Portland Engineering but in the 90's we put down tooling with IVRA/Italy who had them manufactured by Torm...
If your rear brake drums have 1" built in spacers such as all Cooper S and any post 1984 minis, these are the longer drum retaining screws, 2 required per drum and sold individually.
Set of 5 braided hoses. 2 front brakes, 2 rear brakes, and clutch hose for pre A+.
If it is time to replace the brake lines on your Mini, and it probably is, you should consider replacing them with braided-steel hoses. They are direct bolt...
The screw that holds the drum on the hub. Earlier hubs had two screws, many replacements have only one, all that’s needed.
Split pin for the larger size CV joint as fitted to disc brakes. This pin is usually supplied in our normal stock bearing kits. Sold individually.
this will also fit the nut for the rubber cross drive coupling on the gearbox
Mintex brake shoes for the rear of all minis which are 1.25" wide. Also fitted to front on early single leading shoe cars (dry suspension pre 1964) with a single wheel cylinder. Manufactured by Mintex and sold as a box set of 4 brake shoes for one re...
Not included with any brake pads these days owing to universal usage these
pins and retainer clips should always be changed when fitting new pads.
For vehicles with 8.4" discs and standard 2 pot calipers,1984 onwards.
This holds the brake light switch(C16062A) on single line brakes and fits into the 2 way union where the front hose bolts on the other end. Later cars with no switch use C5192A.
8.4" diameter as used standard on all late model Minis with 12 or 13 inch wheels. Our premium quality item. See GBD90806MS for a cheaper option.
Sold individually, but should be replaced as pairs.
Set of 4 Brake pads from the original manufacturer Delphi for the 8.4" wide disc fitted as standard to minis from 1984on with 2.920" pad width.
A set of split pins are available as GBK1010 or with metal retaining clips as [link]...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.