£48.05 exc vat
£57.66 inc vat
In stock
Incorperating the original small clear window to show if the lamp remains switched on.
£48.05 exc vat
£57.66 inc vat
In stockRecommended usage 2 x MSL2030 to fit one mini.
Copies of the originals in vinyl
Incorperating the original small clear window to show if the lamp remains switched on.
Minispares design heavy duty STAINLESS STEEL spotlight bracket, for fitting to cars where it mounts on the front panel valance and grille support panel, giving it perfect rigidity so that the power of the lamp was not impaired. Many cheap aftermarket...
You should always use this kit for fitting any auxiliary spot or fog lamps.
Kit contains wiring and safety relay-cheaper than a burnt out engine compartment.
Please note, SPI and MPI cars have this facility built as standard safety ...
Four LA1009 halogen black bodied driving lamps approximately 170mm wide by 58m deep with 4-XBU10046 stainless steel fitting brackets.
Pair of Chrome WIPAC spotlights. 135mm in diameter, 60mm deep with covers. The lamp is nearly all forward of the mounting bracket making it great for fitting in front of mini grilles. Bulbs are H3 type 55 watts GLB453.
Copies of the originals in vinyl
Incorperating the original small clear window to show if the lamp remains switched on.
Copies of the originals in vinyl
Incorperating the original small clear window to show if the lamp remains switched on.
This is a black painted lighter version with fittings of our s/steel works bar
SEE also C-AJJ3329 for stainless steel.
These cannot be fitted with front overiders and the bottom moulding of the grille slat and back p...
The "Beehive" lens are used throughout the British car range! (Front and rear). Available in various colors: Clear (frosted) GLASS.
Glass "beehive" lenses, either clear or amber, were used on the front turn signals on MKI and MKII Minis...
Copy of the original heavy duty works lamp bar with all fittings but now in stainless steel for longevity.This type was used on LBL66D on the 1967 MONTE CARLO RALLY WITH THEIR NOW LEGAL LIGHTS Consists of a central support bracket and 2 end supports ...
Screw for holding PRC1230A to the number plate light body, 1970 onwards.
This chrome over brass wing side repsater lamp rim will fit of the square/oblong lamp lens where fitted on the wing. Fits straight over the original lens and retained by bending the tag. Made in brass to prevent rusting, but also to obtain that deep...
The best chrome type available with screw and washer.
A headlight trim ring is only the starting point of a good looking car, but you have to start somewhere. Sold singly 2 required per car. These are the original type chrome over solid bras...
Headlamp bulb found in many of the post sealed beam unit cars. An upgrade is available as GLB472X.Sold individually
Two of these plastic lens that hold festoon bulbs (GLB239) are mounted in the metal cast number plate housing (13H6900) on all MK3 bootlids from 1970on. Sold individually with bulb LESS FIXING SCREWS.
See PMZ206 for screw replac...
Clear lens original type stop and tail bulb with offset pins to fit all minis.
Mk1 tail lamps each have a pair of heavy rubber foam gaskets. One between the lens and the chrome base, a similar one between the base and the body. Since they are exposed to the sun and easily visible, faded or rotted gaskets can ruin the look of...
Indicator bulb for all mini domed shape front lamps and all rear lamps. Single filament 12 volt 21 watt. Sold individually.
Chrome plastic D shape type lamp fitted to many cars in the 1960s, the mini usually had two of these in black on the rear number plate of MK1/2 minis/vans and estates.
A metal version is available as BHA4153 and 83H335<...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.