(¥1) £0.96 exc vat
(¥1) £1.15 inc vat
In stock
2H8445 - CLIP
14G8736- BARB (SPIKED CLIP)
ADB4811- STUD
(¥1) £0.96 exc vat
(¥1) £1.15 inc vat
In stockRecommended usage 8 x 2H8445 to fit one mini.
Mk1 style alloy gear knob. Will suit any Mini standatd gear lever thread.
Reinforced elastomer liner for door trim made from VELVEX to prolong the life of your door cards.Die cut on press tools that make the original door cards. Each hole for door locks, window winders, door handles, speaker holes are precision cut to fit ...
Genuine Mini Spares product. The seal that goes on the neck of petrol tanks as protection against water intrusion and to also to make the hole look neater, so replace them when they crack or shrink through heat. This is the original fatter type as us...
Complete car set of roof lining rods, comprising of 1 Red, 2 White, 1 Black, 1 Blue and 1 Yellow
number 1 with red ends is EEB100060
number 2 and 3 is white ends are both EEB100070
number 4 with black ends is EEB100080
...
Full carpet boot liner kit, completely lines the inside of the boot area.
Not suitable for MPI minis.
Used on all MK1/2/3 bootlids there are 26 little holes drilled around the inner edge to hold the seal on and this kit contains the 26 clips. For single clips see 14A6585. Later cars 1988 on fitted a seal to the body only. (CKE10018)
Genuine Mini Spares mouldings product as supplied to Rover.
These are the later door mouldings that prevent water running down the windows into the door causing rust and have the black platic ends fitted for later car safety regulations but ...
An aftermarket version of the mini bumper in stainless steel it has the original type open ends (Rover curled the sharp edges over) - BUMPER BOLTS ARE FITTED BUT NO NUTS -3 required metric M6 thread nuts FS106047
For top qualit...
Don't let the low cost of this "universal" carpet kit fool you. They are made from good-quality nylon carpet with bound edges on the floor pieces to prolong life and look neater. All pieces are pre-cut for easy installation. Made with footpads either...
127cm long and 43cm wide this is enough leather cloth trim that fitted S and deluxe models on the upper and lower facia plus the winscreen A posts. Fitting instructions are included but no glue.
A full set of four arches and two side trims as fitted to all factory cars from 1984 on as standard fitment. Kit includes set of black screws although some were originally held on by pop rivets ADU8629
with headrest-this fixed back special narrow seat was especially designed to work where space is at a premium -Its low back is ideal for sports cars and vintage.Seat can bolt to floor if accessable or on Cobra seat frames--The seat is about 18" wide....
Genuine Mini Spares mouldings product as supplied to Rover.
Pair of the later door outer mouldings plus ADH3809 clips to help prevent water running down the windows causing rust.
These have black plastic ends for car s...
Brake and clutch pedal pads contribute to comfort and safety. They also add that final touch to a nice interior. GPR104 fits brake and clutch pedals of MkI & MkII Minis up to 1976 and the throttle pedal on post 1976-1996 models.
Brighten up your car with these chromed plinths for the wiper wheel box on MK3 Minis on to the very last models. Includes 8 sided nut for all MK3 cars 1970 on.
For MK1/2 see 37H6042C.
Vinyl covered 9 piece black interior trim kit
This kit is for wind up window type doors,for MK3 saloons 1973 onwards (except Cooper S) and contains 2 door trims,2 rear quarter trims,rear parcel shelf,2 rear glove box trims and 2 rear wheel a...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.