(¥2) £2.03 exc vat
(¥2) £2.44 inc vat
In stock
current wheel cylinders are using 7.8mm rather than 6.2mm(1/4")spanner size but same 1/4"unf thread. See 660510 spanner for this size bleed nipple.
genuine AP brake part
(¥2) £2.03 exc vat
(¥2) £2.44 inc vat
In stockRecommended usage 2 x 513118MS to fit one mini.
Washer for 17H2646ORIGINAL brake servo non return valve
Rubber gaiter to keep debris from entering the drum via the backplate handbrake lever SMN10005. Sold singly per backplate, 2 required per car.
Genuine AP Lockheed rubber boot
Set of 4 hoses, 2 front and 2 rear.
Braided brake and clutch hoses have a PTFE inner which helps to eliminate the spongy pedal feel under arduous conditions, and give greater efficiency. The outer braided stainless steel cover e...
Seal for between the brake servo and master cylinder, fits all late 1988 onwards vehicles where the master cylinder was mounted directly to the servo unit.
Replacement rubber grommet for the servo vacuum hose for the 1992 onwards brake servo (GSM119)
We now supply 2 easy bend copper nickel pipes with the correct unions for when converting to the later type GMC227 front to rear split master cylinder.
Correct size and length brake pad pin for the caliper using 8.4" disc size and vented calipers.
Master Cylinder repair kit for repairing the late GMC90376 master cylinder that was attached to the servo from 1995 until the end of production this kit uses a longer seal in conjunction with a nylon bearing. If your master cylinder has a drill hole ...
As the original brake pipe kit is now obsolete, we now supply 2 easy bend copper nickel pipes with the correct unions for when converting to the later type GMC227 front to rear split master cylinder.
For use on 8.4" wide standard brake disc calipers, 2.920"wide.
This is the Ultimax upgrade which produces less brake dust which destroys alloy wheels. For the upgraded version of this see C-AHT16GREEN.
A set of split pins are availa...
Our favourite pads as the give less brake pad dust which destroys alloy wheels.
Very durable and great for most road usage. The green upgrade for fast street is C-8G8995GREEN.
Cooper S 7.5" complete brake disc kit, except for disc shields, with Mini Spares own cast standard calipers. If you want or have 10" wheels this is the kit to convert from drum brakes to discs brakes.
This kit includes every nut bolt and co...
12" wheel to 10" wheel running gear conversion kit. Less wheels.
This kit will convert your 8.4 disc set up to the Cooper S 7.5 discs to allow fitment of 10" wheels, kit includes discs, calipers, kevlar pads with split pins and drive flanges...
Genuine Mini Spares version of the L/H AP caliper as produced by us years ago when not available from AP. Whether you are upgrading from the smaller 997/998 discs to the larger 'S' brakes or simply restoring a Cooper S, you'll appreciate the value o...
Genuine Mini Spares version of the R/H AP caliper as produced by us years ago when not available from AP. Whether you are upgrading from the smaller 997/998 discs to the larger 'S' brakes or simply restoring a Cooper S, you'll appreciate the value of...
Genuine Mini Spares R/H caliper for 8.4" disc set ups remanufactured exclusively for Minispares. Lots of alternatives on the market but AP no longer make the originals but as their largest agent for Mini these are our own and fully tested.
C...
special shaped nut for handbrake cable at handbrake end
Twin cable use 2A5858
The rubber type grip fitted on handbrakes-
will fit any single cable hand brake from 1976 on
Mk1/2 used 13H5541 thinner plastic type--to fit this to pre 1976 early cars you will need to put lots of sticky tape on the h...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.