(¥36) £36.00 exc vat
(¥43) £43.20 inc vat
In stock
(¥36) £36.00 exc vat
(¥43) £43.20 inc vat
In stockRecommended usage 1 x CK19FIXINGSSET to fit one mini.
These are the brackets required for fitting either Spax or Gaz coil over dampers with 1/2"hole on the upper front eye bush.This kit comes complete with all nuts and bolts plus the spacers for either side of the front top damper mounting bolt. The da...
Genuine Mini Spares UK made complete joint with the following specifications,
correct dimensions and shape of pin and ball in EN24T, using correct spec grease,
genuine original shape cup using correct material (21A423MS...
Mini Spares quality suspension kit includes all four adjustable alloy trumpets and knuckle joints plus the two extended rod struts required for the rear. Many people will advise you, why you should consider upgrading to the genuine classic "Hi/Lo" su...
Car set of 4 top Subframe tower mountings for Road cars from 1976-2000.
Aluminum pad for the top of each subframe mounting and a poly pad below to replace the standard rubbers originally fitted. The alloy pads help reduce subframe movement, ...
Kit using budget adjustable suspension Gaz adjustable dampers plus the machined alloy budget adjustable suspension cones.
Ultimate road or race geometry kit which includes following parts. Adjustable tie rods and lower arms with the correct bush kits. For the rear a set of camber and tracking brackets. When fitted the suspension must be properly set up. This kit will dr...
This is a budget way of improving the stability of the front subframe leaving the rear mountings standard for quietness.
It only includes the 4 poly tower spacers and for the front of the front subframe 2 poly spacers and 2 metal washers.
To compliment the top alloy blocks (C-STR640), those troublesome front rubber mountings can be replaced by alloy cast mountings which will not break and further enhance roadholding. These are for the front of the front subframe on vehicles built from...
The set of four aluminum top front subframe mountings are to replace the standard rubbers fitted on vehicles from 1976 to present date. These alloy pads help reduce subframe movement, which is detrimental to handling when driven hard. As the original...
These cone springs will require Hilo adjustable suspension as they sit higher than the originals.Containg an anti fade property and shape which helps them going off during racing and giving hopefully a season of racing before replacement. A softer ro...
Uses 2 Soft standard rubbers on the insides and the 2 Mauve poly on the outside.
HARD OUTERS / SOFT INNERS - STOPS BRAKE WEAVING.
Don't be confused as this special shore hardness set up was proven after 2 years of testing and is per...
The Mini's rear subframe is rubber mounted. Polyurethane (stiffer, much longer lasting) bushes are now available for the rear subframe trunions. Cars manufactured before 1976 can use the same bush (2A5818/POLY) at the front and rear of the subframe, ...
The Mini's rear subframe is rubber mounted. Polyurethane (stiffer, much longer lasting) bushes are now available for the rear subframe trunions. Cars manufactured before 1976 used the same bush 2A5818(C-STR638) at the front and rear of the subframe, ...
Upgraded, lower EN8 damper pin. 3/8"unf. Sold singly
Especially useful for competion cars or street cars with lowered suspension.
Its quite a good idea to change these if they are corroded to give a better seating for your dampers.<...
Mini Spares product UK made especially for use when geometry has been changed, such as fitting adjustable tie rods or lower arms, or on any cars with corrected castor angles.
Set of 4 bushes.
These metal sleeved bushes are specially...
Pair of adjustable tie rods. See 21A1092 tie bar kit.
When you change the length of the lower control arm to attain the desired degree of camber, the caster also changes. To reset it you must be able to change the length of the ...
Pair of upper front damper mounting brackets, with the mounting pin both raised and moved in towards the vehicle centreline slightly to improve damper attitude. With the damper held in a more vertical position they work far more efficiently, improvin...
Rear solid brackets for the front subframe of post 1976 models, ideal for racing or road if noise is not important. But very important if you are after the ultimate handling! we have tried the poly type but they were not as successful.
This is the spacer for fitting either side of the spherical joint or rose joints on lowers arms, made to fit all our lower arms with this type of fitment. Sold individually
A complete kit of coil springs and shocks to replace the old suspension rubber cones and trumpets. This is an adjustable set up for standard height cars with full fitting instructions. This kit really does transform a mini suspension and has been saf...
This is a complete front set only of coil springs & dampers and for lowered suspension (for mounting brackets see CK25)
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.