£378.00 exc vat
£453.60 inc vat
In stock
£378.00 exc vat
£453.60 inc vat
In stockRecommended usage 1 x CK27 to fit one mini.
A single coil spring for the front lowered coil spring type dampers only.
SINGLE FRONT SHOCK ABSORBER USED FOR ANY HEIGHT ON SPAX COIL OVER KIT.
COIL OVER SPRING FOR THIS PART IS A6400. OPEN LENGTH 300MM, CLOSED LENGTH 250MM.
A complete kit of coil springs and shocks to replace the old suspension rubber cones and trumpets. This is an adjustable set up for standard height cars with full fitting instructions. This kit really does transform a mini suspension and has been saf...
New Evolution design in 4mm thick metal mase to fit Genuine and our non genuine subframes better than the standard originals.
The amount a wheel leans in or out at the top is called "camber". As the car turns and the body leans the tire can ...
Mini Spares quality suspension kit includes all four adjustable alloy trumpets and knuckle joints plus the two extended rod struts required for the rear. Many people will advise you, why you should consider upgrading to the genuine classic "Hi/Lo" su...
Kit using budget adjustable suspension Gaz adjustable dampers plus the machined alloy budget adjustable suspension cones.
one piece forged lower rod end arms
unbelievably at this price they are not the welded type as sold by many of our competitors
Same as the C-AJJ3360 lower arm kit, but includes the spherical rod ends,spacers and dustcov...
Ultimate road or race geometry kit which includes following parts. Adjustable tie rods and lower arms with the correct bush kits. For the rear a set of camber and tracking brackets. When fitted the suspension must be properly set up. This kit will dr...
Performance geometry kit includes tie bars, lower arms plus performance bushes for lower arms and tie rods. This is basicaly the same kit as MSSK3013 but less the rear tracking and camber brackets.
parts in kit to transform hand...
E coated Mini Spares product. Have a look at your subframe because if it looks bad then you need a new one for your MOT. Don't forget to renew the bushes and bolts.If you have the 1991 on type with mounting prongs for the exhaust rubber straps then y...
These shafts have changed diameter thickness over the years but these are the
original thick type and upgraded to EN24 for competition or standard uses.
this is the right hand longer one.
Complete rebuild kit for rear radius arm as sold by us since 2005.
Beware of cheap imports that are available in the market as they do not have correct heat treatment where required and have no longevity.
Kit Includes: shaft, beari...
Lower arm top hat bush in poly to fit all lower arms with twin taper as standard from 1965. Mini Spares have upped the game once again with these superbly finished bushes which surpass anything on the market. Fitted with a metal bush insert these are...
Uses 2 Soft standard rubbers on the insides and the 2 Mauve poly on the outside.
HARD OUTERS / SOFT INNERS - STOPS BRAKE WEAVING.
Don't be confused as this special shore hardness set up was proven after 2 years of testing and is per...
Mini Spares own to original drawing specifications with heat treatment correctly applied where appropiate.Lack of proper maintenance (grease) will make the pivot shaft and/or bearings wear that much faster. In severe cases the shaft may rust to the b...
Genuine correct length with cut outs and drain holes in the correct places.
The MK3 door seal is notable because of it's large 'bulb' area. The 'bulb' is the round section that the door closes against. The size is determined by how much gap ...
complete kit of bushes and bolts for pre 1976 rear subframes when 8 rubber bushes the same size are used--for cars after 1976 with 4 small and 2 large rubber bushes use MS43
Rubber mounts are made in the UK.
It has been said that one of the biggest improvements that can be made to a Mini is to replace the rubber cone springs. When that statement was made it referred to new rubber cones… there is now a new standard in Mini springing: coil springs! This di...
The Mini's rear subframe is rubber mounted. Polyurethane (stiffer, much longer lasting) bushes are now available for the rear subframe trunions. Cars manufactured before 1976 can use the same bush (2A5818/POLY) at the front and rear of the subframe, ...
Upgraded, lower EN8 damper pin. 3/8"unf. Sold singly
Especially useful for competion cars or street cars with lowered suspension.
Its quite a good idea to change these if they are corroded to give a better seating for your dampers.<...
Mini Spares product UK made especially for use when geometry has been changed, such as fitting adjustable tie rods or lower arms, or on any cars with corrected castor angles.
Set of 4 bushes.
These metal sleeved bushes are specially...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.