ALTERNATOR FLANGED BOLT M8x20
FS108207

($1.37) £1.37 exc vat

($1.64) £1.64 inc vat

In stockIn stock
THE M10 METRIC bolt 25mm long for holding alternator plus other parts on the Twin point minis

($1.37) £1.37 exc vat

($1.64) £1.64 inc vat

In stockIn stock

Recommended usage 3 x FS108207 to fit one mini.
Alternators and Starter - Qty 3
Alternators and Starter - Qty 4
Alternators and Starter - Qty 1

People also bought products

Stainless steel tailpipe trim with hanger bracket designed for fitting to the tailpipe of RC40 rear box as an extension piece. This is part of our RC40PACKAGE015 kit for Van/Estate and Pickup exhaust system when a freeflow o...

M10 metric flanged bolt 35mm long for catalytic converter. (4 required per unit)

This is the clamp on the cooper freeflow manifold to clamp it to the engine for extra support, supplied with tag.

THE M10 METRIC NUT THAT SCREWS ON THE THREAD BOLTS OF THE CATALYLITIC CONVERTER

Special reinforced gasket for injection cars has metal inserts on exhaust ports plus a metal back on the manifold side which makes surface easier to clean when replacing. Often used on Turbo cars when correct gasket is in short supply.


...

This is the stainless steel pipe that bolts to the catalyst and then allows you to fit the rear silencer of your choice.

The popular RC-40 exhaust system was updated to the Millennium range in 2000. All retain the optimum size 1.75" tubing for maximum performance and efficiency, but we now offer a choice of tailpipe size and configuration. Front pipes come either "str...

The popular RC-40 exhaust system has been updated. All retain the optimum size 1.75" tubing for maximum performance and efficiency, but we now offer a choice of tailpipe size and configuration. This is a stainless steel centre exit with large bore 2....

LONG CENTRE BRANCH EXHAUST MANIFOLD FOR FUEL INJECTED CARS WITH A SENSOR TAKE OFF in main LCB body, THIS IS FOR USE WHEN THE CATALYST IS BEING REMOVED AND A RC40 EXHAUST IS BEING FITTED. If the catalyst is to be retained use [link]C-AEG3...

if your front downpipe or exhaust needes replacing this conversion will give you extra power for little more. A new better flowing downpipe with a flexible knuckle plus our super RC40 single box rear silencer for that slightly sporty sou...

Maniflow's tubular reproduction of the original Cooper 997/998cc exhaust manifold manufactured out of the same tubing as the STD bore LCB. This free flow manifold works vey well at lower speed pick up, the LCB is noisier but better at the top end of ...

Special tin plate type of gasket that goes between the manifold and exhaust downpipes on all injection cars.

The very rear bobbin type mounting rubber on every mini made until the introduction of a rubber hanger strap in 1992. When the RC40 or similar systems are fitted, 2 will be required.

See C-19G3258 for larger upgrade...

Standard bore LCB (inch and three quarters internal diameter) for post 1990 cars with catalyst that is ideal for for standard to high performance 1275s and for street 1380s. The best quality production manifold is made by Maniflow. The Long Centre B...

Locating rings originally made for 12G295 heads with twin carbs to line up the inlet manifold to the inlet ports on the cylinder head it found its way on most twin carb factory produced cars. There is a recess in the inlet port on the he...

Manifold gasket fitted to all A series pre 1992 except Turbo which had a reinforced exhaust ports GUG704063MG and SPI from 199. From 1991 on a new better gasket with reinforced exhaust ports and backing was fitted GUG704053MG

This bracket bolts on the gearbox and attaches to the exhaust front downpipe clip GEX7053.

Clamp on the front downpipe that fits to the bracket on the gearbox (GEX7526)

these are also supplied on our new 2 piece exhaust.

Complete mounting kit for the RC40 exhaust. Includes all new rubber mounts, brackets and clamps.