DISTRIBUTOR ORIGINAL MINI 25D TYPE WITH VAC UNIT
GEU930

($43.83) £43.83 exc vat

($52.60) £52.60 inc vat

In stockIn stock
Range of distributors with modern day curves built,programmed and tested for Mini Spares in UK.

Beware of cheap China made units that are poorly made- see note at bottom. GEU930 25D 850/early 998

12G2140 23D Cooper S non vac

BAU1962 45D 998/1098

ADU5789 59D 998 A plus

12G4180 45D 1275cc with vac, good for modified road tune engines

ADU3825 59D 1275 with vac, A Plus good for modified road tune

For electronic versions add suffix MS- example= ADU5789MSA Non Genuine reproduction distributor with vac-unit suitable for 850/998cc. With modern day curves it even works on 1275cc. A worn out distributor can cost you both performance and economy. Precise spark timing and distribution is the job of the distributor. Merely replacing the points and condenser will not fix the chronic problem of worn out bushes and shaft. These look like the originals apart from vac unit with push on connector.

Most A-Series cars had a vacuum advance distributor, only the Cooper "S 12G2140 had a full centrifugal version. The vacuum is designed to retard the timing under heavy load thus decreasing the chance of detonation. These units are guaranteed to out-perform your old tired version. The best test is to put a timing light on your car and watch as timing marks on the flywheel dance and bounce around as the engine changes speed, etc. Install a new distributor and try it again!! All the bounce will never go completely away as long as you are driving the distributor through a timing chain gear set to the crankshaft.



DODGY DISTRIBUTORS-made in China and sold by some vendors

We’ve seen distributors with all different curves in the same batch. Base plates

that stick and alter the curves, sometimes jamming in full advance. When tested

we had difficulty getting them to run correctly when using a timing light and we

found that the rotor arm and dog at the bottom of shaft was often out of phase

putting the rotor arm in wrong position in relation to the point at where the spark

fired. We also found rotor arms that were hard up against the carbon bush in the

top of distributor cap causing the cap to burn away in middle.

Having tried and tested countless suppliers of imported and British made

distributors we had all ours individually built and tested to prevent costly engine

failures and breakdowns for the following reason - those suppliers were unable

to advise what curves were in them - we rarely found them the same in any

batch! Every part, even so-called ‘Mini Spares branded parts’ are being copied

for financial gain as Minis climb in popularity and value. Unscrupulous

companies can get parts made cheaply overseas, but they lack the technical

knowledge and precision required to make them correctly

($43.83) £43.83 exc vat

($52.60) £52.60 inc vat

In stockIn stock

Recommended usage 1 x GEU930 to fit one mini.
Distributors - Qty 1

Alternative products

Pre A Plus Electronic Ignition distributor with vac unit, modified to our specification in the UK to give best performance on any minis with std to 276 camshaft profile.

Brand New distributor complete with electronic conversion already fitt...

People also bought products

Pre A Plus Electronic Ignition distributor with vac unit, modified to our specification in the UK to give best performance on any minis with std to 276 camshaft profile.

Brand New distributor complete with electronic conversion already fitt...

Fits our 45/59d distributors, 1275cc as fitted to 12G4180 and ADU3825

Along with our distributor manufacturer we have found this to be the best for modern day fuels for all 45 or 59d distributor for 1275cc uses as...

RESIN BASED CONDENSER as per the original Lucas type made for the 23/25D type distributor as fitted to original Cooper S or Racers who want a trusty part or where originality is required,with soldered wire connections and correctly made foot to sit ...

NEGATIVE EARTH ONLY..Reproduction CONTACTLESS Distributor suitable for modern day fuels for 850 and 998cc pre 1974 with upgraded rotor arm "Negative earth only". A worn out distributor can cost you both performance and economy. Precise spark timing ...

Electronic Distributor for any standard A+ 998cc. Negative earth only.



From 1982on 998cc were fitted with a ballast coil which means a new wire must be fitted from fusebox top left terminal where there is a large white cable to the...

NEGATIVE EARTH ONLY..45D electronic(contactless)Pre A plus distributor .

replaces 41824A and 41418 plus any 998/1098cc up to the changeover of A plus type distributors. For best performance and tune we advise our electronic evolution versio...

NEGATIVE EARTH ONLY. Cooper"S" 23D distributor, no vac unit-This is NOT THE ORIGINAL LUCAS ITEM but a new contact less electric copy of 40819 to cope better with modern day fuels. Fitted with the better Red rotor arm upgrade.Cheaper than many electro...

These are the screws needed to fix the condenser, points and base plate to 23/25D distributors. See 57H5135 for 45D type distributors.

Replacement distributor cap retaining clip for all 45D type distributors-sold per clip.

Electronic Ignition distributor, fitted as standard to all 1300 Carb Cooper models. Also Metro 1275cc engine.

Replacement service items for this are:

Cap GDC156

Rotor arm GRA2143

Should be used with GC...

the oil seal to fit on 12A1136 distributor housing. Pre A Plus

the earlier housing 2A612 did not have a seal.

If you have an original 25D type distributor this is an upgraded arm (blade moulded and riveted )for performance use because all the other types available now are likely to fail at high revs. Because the blade is thin,or the rivet sometimes to long a...

The all new 123 Electronic distributor is now available at Minispares. Featuring 16 ready programmed switchable advanced curves built in as standard, a must for any mini with a worn distributor. Full instructions are included with the system. For an...

The O ring that actually sits on the distributor drive spindle shaft in the recess provided.

The stock vacuum advance distributor is connected to the carb/manifold by a small rubber joint that in turn is mated to metal line that fits the distributor. If the little rubber connector is deteriorated it could allow a vacuum leak at the carb and ...

This "Pigtail" wire is all that carries current through the distributor to the points.Fits 23 and 25d type distributors

Top-entry cap takes plug-in wires and will interchange with GDC102. This is an alternative for side entry cap GDC102 which some believe is less prone to wet-weather problems. Features aluminium contacts.

This distributor clamp should not be bent; if it is, either you can't get the dizzy all the way in or it won't grip.

Modified by Aldon to their Yellow distributor spec on 45/59D type body with vacuum advance for Aplus performance road engines.

Once the engine has been modified, it will invariably require a different ignition curve-especially when comp...

Straight rubber connector pipe. The standard vacuum advance distributor is connected to the carb/manifold by a small rubber joint that in turn is mated to metal line that fits the distributor. If the little rubber connector is deteriorated it could a...