£277.50 exc vat
£333.00 inc vat
In stock
'The 123 Distributor can be used with 6 or 12 voly power supplied from
the coil be it ballast resisted or not providing the coil has no less
than 1 Ohm resistance'.
£277.50 exc vat
£333.00 inc vat
In stockRecommended usage 1 x C-27H7771 to fit one mini.
100% silcone translucent outer sheath, 8mm lead set with stainless steel wire spiral bound wire giving instant and greater resonance, Kevlar fibre core and a ferromagnetic layer for EMC suppression by Luminition. Top end of ignition lead sets.
Original mini coil fitted to all cars up to 1983.
3ohms
NOT for ballast type ignition systems.
Our research, sales and feed back shows Intermotor coils to be the best available for the mini.
Original type coil bra...
The all new 123 Electronic distributor is now available at Minispares. Featuring 16 ready programmed switchable advanced curves built in as standard, a must for any mini with a worn distributor. Full instructions are included with the system. For an...
the oil seal to fit on 12A1136 distributor housing. Pre A Plus
the earlier housing 2A612 did not have a seal.
The all new 123 Electronic distributor is now available at Minispares. Featuring 16 pre programmed advanced curves built in, a must for any mini with a worn distributor. Full instructions are included with the system. For any A series, A Plus engines...
The stock vacuum advance distributor is connected to the carb/manifold by a small rubber joint that in turn is mated to metal line that fits the distributor. If the little rubber connector is deteriorated it could allow a vacuum leak at the carb and ...
This distributor clamp should not be bent; if it is, either you can't get the dizzy all the way in or it won't grip.
Straight rubber connector pipe. The standard vacuum advance distributor is connected to the carb/manifold by a small rubber joint that in turn is mated to metal line that fits the distributor. If the little rubber connector is deteriorated it could a...
Fited to Lucas type distributors with 45D body in 1974 until 1990 when electronic type that was held on by 2 screws appeared as oppossed to this clip on this type. If you need a new distributor clip-we have them as GDC136CLIP.
Lots of things have been written about performance plug ignition wires but regardless of what you believe we all know that good wires are a must. This special competiton wires set from the Lucas factory has 8mm wire and the highest performance, no br...
best plug for 12g295 head as fitted to 998 cooper--for tuned head use B7ES.
this is good for any head where a lot has been machined off-flat top pistons.
Coil bracket fitted to end stud of cylinder head,clutch end for coil to mount on as fitted 1969-94-MK3 on. This has been made to the original specification with the welded lug nuts rather than the cheaper method of having just plain holes to take a b...
Best on the market, sports coil-Not Lucas. A standard coil can only do so much, and when compression is raised (as in most high performance engines) or improper fuel mixtures occur something better is needed. This sports gold coil with proven origina...
Replacement rotor arm for the Electronic 123 range of distributor.
Original mini coil fitted to all cars up to 1983.
3ohms
NOT for ballast type ignition systems.
Our research, sales and feed back shows Intermotor coils to be the best available for the mini.
Original type coil bra...
Quality HT lead set for twin point injection minis. For use with M4 type coil. Spiral bound wire giving instant greater resonance.
This is the standard non ballast coil as used on the late Mini with factory electronic ignition for use with 65D distributor.0.9ohms.
GCL143 was the Genuine Rover part fitted part on 1275cc from 1990.
0.9ohms
GCL2...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.