£29.79 exc vat
£35.75 inc vat
In stock
Parts are available seperately:
The plastic clips are 13H6461.
Upper bracket is NJU10002 x 2 required.
Lower bracket is JZV1073.
NJT10004 for plastic cover only.
The 2 upper brackets fit on the rocker cover retaining nuts and the lower bracket fits on the gearbox with the square fastener hole towards the oil filter side. You will have to remove the gearbox to engine bolts. Start with the middle bolt first (there are 5 bolts) so you can see where the bracket needs to fit and the bolt to the left, nearer to the starter is the other bolt needed to remove.
£29.79 exc vat
£35.75 inc vat
In stockRecommended usage 1 x BHM1675 to fit one mini.
The current large plastic shield without any fittings or clips, to cover the engine electrics. Might need slight modifications for some SPI cars but we have fitted them on our own cars without any problems.
The plastic clips are available as...
The current large plastic shield with fittings to cover the engine electrics on Automatic engines.With upper 2 plastic clips-- The plastic clips are available as 13H6461---These are BHM1675 but cut 4.75" shorter with a slot for the lower...
Each clip kit has 3 parts, clip, spacer and turnbutton. Each kit sold separately and 3 kits per car are required.Now in black to match shield and not show dirt or grease
This is the button with a spade on the end which often breaks, which ho...
The current large plastic shield without any fittings or clips, to cover the engine electrics. Might need slight modifications for some SPI cars but we have fitted them on our own cars without any problems.
The plastic clips are available as...
Bracket for attaching the Distributor water shield block to gearbox stud/bolt
Does not come with fixing clips, these are available seperately as part number 13H6461
Upper bracket-NJU10002
Lower bracket- JZV1073
The...
Bracket for attaching the Distributor water shield to the rocker cover bolts.
Does not come with fixing clips, these are available seperately as part number 13H6461.
Electronic ignition conversion. For points type distributors, fixed or sliding. Negative earth only. Also, available for earlier 23/25D on Negative earth (LU142) or earlier 23/25D with Positive earth (LU142AP12).
ONLY use GCL217 coil for bal...
Pre A plus Electronic Ignition distributor, with vac unit modified to give better performance on any minis with 285/286/296 camshaft profiles
Brand New distributor complete with electronic conversion already fitted.
PRE A PLUS
<...
Pre A Plus Electronic Ignition distributor with vac unit, modified to our specification in the UK to give best performance on any minis with std to 276 camshaft profile.
Brand New distributor complete with electronic conversion already fitt...
RESIN BASED CONDENSER as per the original Lucas type made for the 23/25D type distributor as fitted to original Cooper S or Racers who want a trusty part or where originality is required,with soldered wire connections and correctly made foot to sit ...
Electronic Distributor for any standard A+ 998cc. Negative earth only.
From 1982on 998cc were fitted with a ballast coil which means a new wire must be fitted from fusebox top left terminal where there is a large white cable to the...
NEGATIVE EARTH ONLY..45D electronic(contactless)Pre A plus distributor .
replaces 41824A and 41418 plus any 998/1098cc up to the changeover of A plus type distributors. For best performance and tune we advise our electronic evolution versio...
The all new 123 Electronic distributor is now available at Minispares. Featuring 16 ready programmed switchable advanced curves built in as standard, a must for any mini with a worn distributor. Full instructions are included with the system. For an...
Best on the market, sports coil-Not Lucas. A standard coil can only do so much, and when compression is raised (as in most high performance engines) or improper fuel mixtures occur something better is needed. This sports gold coil with proven origina...
CSI-Ignition is a fully electronic ignition built in an original housing. You will have to remove the cap to see the difference!Neg earth only
After removing the cap you can select between 16 different curves by using
a screwdriver....
CSI-Ignition is a fully electronic ignition built in an original housing. You will have to remove the cap to see the difference! Neg earth only
After removing the cap you can select between 16 different curves by using
a screwdriver...
These are the screws needed to fix the condensor, points, base plate and vacuum to 45D and 59D distributors. For 23/25D type see 17H5106
These are the screws needed to fix the condenser, points and base plate to 23/25D distributors. See 57H5135 for 45D type distributors.
Replacement distributor cap retaining clip for all 45D type distributors-sold per clip.
Bracket for attaching the Distributor water shield block to gearbox stud/bolt
Does not come with fixing clips, these are available seperately as part number 13H6461
Upper bracket-NJU10002
Lower bracket- JZV1073
The...
Electronic Ignition distributor, fitted as standard to all 1300 Carb Cooper models. Also Metro 1275cc engine.
Replacement service items for this are:
Cap GDC156
Rotor arm GRA2143
Should be used with GC...
Replacement Distributor ignition module fitted to all standard electronic ignition distributors (non injection) looking at the front of module, negative is on the left. positive on right and centre pin is not used.
the oil seal to fit on 12A1136 distributor housing. Pre A Plus
the earlier housing 2A612 did not have a seal.
If you have an original 25D type distributor this is an upgraded arm (blade moulded and riveted )for performance use because all the other types available now are likely to fail at high revs. Because the blade is thin,or the rivet sometimes to long a...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.