DISTRIBUTOR CSI 43/45D ELECTRONIC WITH VACUUM ADVA...
C-27H7712

£240.00 exc vat

£288.00 inc vat

In stockIn stock
CSI-Ignition is a fully electronic ignition built in an original housing. You will have to remove the cap to see the difference!Neg earth only

After removing the cap you can select between 16 different curves by using

a screwdriver. A bright flashing led light shows which curve you have selected.

Each CSI dizzy comes with 16 pre programmed maps, this one suitable for all Pre A+ 850, 997, 998, 1100 and non cooper S 1275's

See C-27H7713 for non vac unit peformance variant. Use with 3ohm coil GCL216.

£240.00 exc vat

£288.00 inc vat

In stockIn stock

Recommended usage 1 x C-27H7712 to fit one mini.

People also bought products

Electronic ignition conversion. For points type distributors, fixed or sliding. Negative earth only. Also, available for earlier 23/25D on Negative earth (LU142) or earlier 23/25D with Positive earth (LU142AP12).

ONLY use GCL217 coil for bal...

These are the screws needed to fix the condensor, points, base plate and vacuum to 45D and 59D distributors. For 23/25D type see 17H5106

This distributor clamp should not be bent; if it is, either you can't get the dizzy all the way in or it won't grip.

The current genuine large plastic shield with all fittings required to cover the engine electrics.

Parts are available seperately:

The plastic clips are 13H6461.

Upper bracket is NJU10002 x 2 requ...

Fited to Lucas type distributors with 45D body in 1974 until 1990 when electronic type that was held on by 2 screws appeared as oppossed to this clip on this type. If you need a new distributor clip-we have them as GDC136CLIP.

Lots of things have been written about performance plug ignition wires but regardless of what you believe we all know that good wires are a must. This special competiton wires set from the Lucas factory has 8mm wire and the highest performance, no br...

original Lucas type RESIN BASED CONDENSER made for the 45/59D type distributor if you want a quality item rather than the cheaper inferior parts available. Filled with 3m of winding inside as per original Lucas but every copy analysed to date has ...

Best on the market, sports coil-Not Lucas. A standard coil can only do so much, and when compression is raised (as in most high performance engines) or improper fuel mixtures occur something better is needed. This sports gold coil with proven origina...

Original mini coil fitted to all cars up to 1983.

3ohms

NOT for ballast type ignition systems.

Our research, sales and feed back shows Intermotor coils to be the best available for the mini.

Original type coil bra...

Rotor arm for all A series electric distributors when points are not fitted, except for turbo. The distributor cap for this rotor arm is GDC156.

A higher compression engine should have a colder spark plug. The engineers explain that it has to do with flame temperature and overheating the plug. I know from experience that my race engine will melt a street plug. Choose from the following NGK pl...

great plug for flat top pistons or 12G295 head when tuned engine.

This was the first mini distributor cap to have screws hold the cap to the body from about 1990 on, when electonic ignition was introduced. Therefore there is no points or condenser but the rotor arm to use is GRA2143. Fits all 1992 onwa...

These points were fitted from 1974-80 when the distributors became a 45D type,

the distributor cap shape changed also to GDC136 and likewise rotor arm GRA2114 and condenser GSC2109.

This is the standard non ballast coil as used on the late Mini with factory electronic ignition for use with 65D distributor.0.9ohms.



GCL143 was the Genuine Rover part fitted part on 1275cc from 1990.

0.9ohms

GCL2...

Slightly hotter running engine plug for A Plus 998 and all 1275cc standard engines. For engine running CR of 9.4 to 10:1

The original blue rotor arm was fited with a blue cap GDC143 to the turbos and were made stronger by moulding and riveting the contact plate to the arm, so if you are looking for an upgrade on your 45D body distributor this is our altern...

100% silicon insulation, silicon coated suppressed conductor,braided glass reinforcement,increased working temperature 0f minus 50C to +300 degrees with improved resistance to damp and water, great fitting and spiral bound wire giving instant and gre...

Fitted as standard to single points and twin points. NGK later plug BPR6EVG is also recommended. Sold singly

Standard heat plug for all 850/998cc low compression engines up to 9.4:1 CR.

A plus 998 engines with flat top pistons use BP6ES which run hotter with 88 degree thermostats use BP6ES also.