£225.00 exc vat
£270.00 inc vat
In stock
After removing the cap you can select between 16 different curves by using
a screwdriver. A bright flashing led light shows which curve you have selected.
Each CSI dizzy comes with 16 pre programmed maps, this one suitable for modified Pre A+ Mini Cooper S and other tuned engines.
For engines with vac unit see C-27H7710 Use with 3ohm coil GCL216.
£225.00 exc vat
£270.00 inc vat
In stockRecommended usage 1 x C-27H7711 to fit one mini.
Cooper"S" 23D distributor, no vac unit-This is NOT THE ORIGINAL LUCAS ITEM as the original company and tooling no longer exist but is a new copy of the 40819 to work better with modern day fuels. It does have an original type baseplate with a post b...
RESIN BASED CONDENSER as per the original Lucas type made for the 23/25D type distributor as fitted to original Cooper S or Racers who want a trusty part or where originality is required,with soldered wire connections and correctly made foot to sit ...
CSI-Ignition is a fully electronic ignition built in an original housing. You will have to remove the cap to see the difference!
After removing the cap you can select between 16 different curves by using
a screwdriver. A bright flas...
These are the screws needed to fix the condenser, points and base plate to 23/25D distributors. See 57H5135 for 45D type distributors.
the oil seal to fit on 12A1136 distributor housing. Pre A Plus
the earlier housing 2A612 did not have a seal.
If you have an original 25D type distributor this is an upgraded arm (blade moulded and riveted )for performance use because all the other types available now are likely to fail at high revs. Because the blade is thin,or the rivet sometimes to long a...
The O ring that actually sits on the distributor drive spindle shaft in the recess provided.
This "Pigtail" wire is all that carries current through the distributor to the points.Fits 23 and 25d type distributors
This distributor clamp should not be bent; if it is, either you can't get the dizzy all the way in or it won't grip.
Designed to fit the GDC102 side entry distributor cap as a protection against water, made in rubber.
for 23/25D distributor but see [link]47H5250[/link} for resin type upgrade with 3m of wire as opposed to every aftermarket type analysed with only 1.5m of wire.
its worth paying extra for the condenser and rotor arm [link]GRA101]/link]
this is the original mini distributor cap where the leads were secured by screws and was fitted to the 25D range of lucas distributors. This cap had side entry leads [link[GHT101]/link] and is now only available from one or two manufactures owing to ...
Lots of things have been written about performance plug ignition wires but regardless of what you believe we all know that good wires are a must. This special competiton wires set from the Lucas factory has 8mm wire and the highest performance, no br...
Coil bracket fitted to end stud of cylinder head,clutch end for coil to mount on as fitted 1969-94-MK3 on. This has been made to the original specification with the welded lug nuts rather than the cheaper method of having just plain holes to take a b...
Best on the market, sports coil-Not Lucas. A standard coil can only do so much, and when compression is raised (as in most high performance engines) or improper fuel mixtures occur something better is needed. This sports gold coil with proven origina...
Original mini coil fitted to all cars up to 1983.
3ohms
NOT for ballast type ignition systems.
Our research, sales and feed back shows Intermotor coils to be the best available for the mini.
Original type coil bra...
Rotor arm for all A series electric distributors when points are not fitted, except for turbo. The distributor cap for this rotor arm is GDC156.
A higher compression engine should have a colder spark plug. The engineers explain that it has to do with flame temperature and overheating the plug. I know from experience that my race engine will melt a street plug. Choose from the following NGK pl...
This was the first mini distributor cap to have screws hold the cap to the body from about 1990 on, when electonic ignition was introduced. Therefore there is no points or condenser but the rotor arm to use is GRA2143. Fits all 1992 onwa...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.