£3.50 exc vat
£4.20 inc vat
In stock
Does not come with fixing clips, these are available seperately as part number 13H6461
Upper bracket-NJU10002
Lower bracket- JZV1073
The...
£3.50 exc vat
£4.20 inc vat
In stockRecommended usage 1 x JZV1073 to fit one mini.
The current large plastic shield without any fittings or clips, to cover the engine electrics. Might need slight modifications for some SPI cars but we have fitted them on our own cars without any problems.
The plastic clips are available as...
Bracket for attaching the Distributor water shield to the rocker cover bolts.
Does not come with fixing clips, these are available seperately as part number 13H6461.
Electronic Ignition distributor, fitted as standard to all 1300 Carb Cooper models. Also Metro 1275cc engine.
Replacement service items for this are:
Cap GDC156
Rotor arm GRA2143
Should be used with GC...
The stock vacuum advance distributor is connected to the carb/manifold by a small rubber joint that in turn is mated to metal line that fits the distributor. If the little rubber connector is deteriorated it could allow a vacuum leak at the carb and ...
This distributor clamp should not be bent; if it is, either you can't get the dizzy all the way in or it won't grip.
Straight rubber connector pipe. The standard vacuum advance distributor is connected to the carb/manifold by a small rubber joint that in turn is mated to metal line that fits the distributor. If the little rubber connector is deteriorated it could a...
for 23/25D distributor but see [link]47H5250[/link} for resin type upgrade with 3m of wire as opposed to every aftermarket type analysed with only 1.5m of wire.
its worth paying extra for the condenser and rotor arm [link]GRA101]/link]
Fited to Lucas type distributors with 45D body in 1974 until 1990 when electronic type that was held on by 2 screws appeared as oppossed to this clip on this type. If you need a new distributor clip-we have them as GDC136CLIP.
Lots of things have been written about performance plug ignition wires but regardless of what you believe we all know that good wires are a must. This special competiton wires set from the Lucas factory has 8mm wire and the highest performance, no br...
original Lucas type RESIN BASED CONDENSER made for the 45/59D type distributor if you want a quality item rather than the cheaper inferior parts available. Filled with 3m of winding inside as per original Lucas but every copy analysed to date has ...
Bracket for attaching the Distributor water shield to the rocker cover bolts.
Does not come with fixing clips, these are available seperately as part number 13H6461.
The current large plastic shield without any fittings or clips, to cover the engine electrics. Might need slight modifications for some SPI cars but we have fitted them on our own cars without any problems.
The plastic clips are available as...
Rotor arm for all A series electric distributors when points are not fitted, except for turbo. The distributor cap for this rotor arm is GDC156.
This was the first mini distributor cap to have screws hold the cap to the body from about 1990 on, when electonic ignition was introduced. Therefore there is no points or condenser but the rotor arm to use is GRA2143. Fits all 1992 onwa...
This is the standard non ballast coil as used on the late Mini with factory electronic ignition for use with 65D distributor.0.9ohms.
GCL143 was the Genuine Rover part fitted part on 1275cc from 1990.
0.9ohms
GCL2...
MK1/2/EARLY MK3. 3 position spring loaded type. Comes with barrel.
For barrel only use part number 24G1345.
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.