RADIATOR 1991-1996 CLIP TYPE SENSOR HOLE IN BOTTOM
GRD172

($68.80) £68.80 exc vat

($82.56) £82.56 inc vat

In stockIn stock
Sensor type Radiator that uses the original Rover clip in type sensor hole in the bottom which was fitted from 1991 up until the introduction of the twin point front mounted type.

This is a Cuprobraze 3 tube modern design version with 9 gills/fins per inch. Cuprobraze is the latest use of brazing in place of traditional soldering to join copper and brass components of radiators which can also use alloys that are stronger than conventional lead-tin solders. Brazed joints are stronger than soldered types which can allow for thinner metal to be used than that for usual copper/brass rads. This improvement led to a further advantage in that cross sections gave higher heat transfer as well as being potentially stronger, lighter,more efficient and potentially smaller. The main benefit is a cheaper to produce better product.

The basic heating problem on earlier cars is the lack of water capacity and an electric fan. Also all the late minis have 5/8" bore heater hoses as opposed to the old 1/2" bore.

The upgrade option to this radiator is C-ARA4443

($68.80) £68.80 exc vat

($82.56) £82.56 inc vat

In stockIn stock

Recommended usage 1 x GRD172 to fit one mini.
Radiators pre 1996 - Qty 1

Recommended products

From 1992, this is the switch as fitted by the factory on the bottom of their radiators and has a seal CDU2334 which is supplied. The retaining clip is KTP9002. Mini Spares radiators are made with screw in type switches to s...

This is the rubber seal that holds the transmitter GVS104 in the bottom tank of the radiator on late cars. The seal is supplied with a new switch and all is held in by KTP9002 retaining clip which should be chamged for safet...

From 1992 mini radiators were fitted with a push in thermal transmitter GVS104 and this is the clip to hold it and the seal in place. The rubber seal is supplied on the transmitter but also available as CDU2334. Minispares r...

Fitted from A plus on to increase engine running temperature. If your radiator has a sender unit in the bottom you may have an expansion tank and therefore the radiator will need a better sealing pressure cap which allows a small vacuumGRC20...

m6x10 bolt--ideal for radiators with metric fittings (6 required for rads)

original imperial radiator screws were SH604031 or PK type were ARA1117

Alternative products

Same as C-ARA4442 but supplied with a screw-in heat sensor unit, as required and fitted initially by Rover to SPI cars. Minispares adapted the safer screw type sensor as compared to the push and turn fit used by Rover, which on certain v...

People also bought products

Silicone hose kit for 998 vehicles from 1989 onwards that were equipped with the plastic inline heater valve, comes complete with moulded heater take off pipe and 5/8 heater pipe.

Original 7/16" spring type hose clip as used on later cars (approx 1990 on) for some radiator hoses and fuel lines.

MPI only. 3 YEAR GUARANTEE-UK made.Large impeller higher capacity water pump. Mini Spares procured product as original Rover Airtex tooling has been scrapped.

Fitted with a PPS, glass filled plastic impeller as used by Jaguar and Aston Marti...

3 YEAR GUARANTEE-UK made.Large impeller higher capacity water pump with top quality die cast body . Mini Spares procured product as the original superb Rover Airtex tooling has been scrapped.

Fitted with a PPS, glass filled plastic impeller...

3 YEAR GUARANTEE-UK made. Large impeller higher capacity water pump with a high quality die cast body. A Mini Spares procured product as the original superb Rover Airtex tooling has been scrapped.

Fitted with a PPS, glass filled plastic impe...

This is the metric nut needed for PQR10028 tensioner as fitted to all mpi mini's.

m6x10 bolt--ideal for radiators with metric fittings (6 required for rads)

original imperial radiator screws were SH604031 or PK type were ARA1117

Replacement electric fan assembly complete with laser cut metal brackets so that it can be mounted to the original mounting points of the standard fan

uses 9" blowing air fan.

Radiator hose kit for all spi Minis. This kit has top and bottom radiator hoses and 2 lengths of heater hoses…all in shiney red Silicone that should last forever and not degrade with heat, time and environment. This kit is ideal for both the racer wh...

Radiator hose kit for all spi Minis. This kit has top and bottom radiator hoses and 2 lengths of heater hoses…all in shiney black Silicone that should last forever and not degrade with heat, time and environment. This kit is ideal for both the racer ...

Radiator hose kit for all spi Minis. This kit has top and bottom radiator hoses and 2 lengths of heater hoses…all in shiney blue Silicone that should last forever and not degrade with heat, time and environment. This kit is ideal for both the racer w...

Unless your're heavily into the concours scene you'll love these hoses! These silcone hoses will withstand higher temps and pressures and will last virtually forever! Made to fit 1275cc cylinder head the length is made to cover 1275cc engines includi...

Black Silicon Bottom hose- Unless you're heavily into the concours scene you'll love these hoses! These silicone hoses will withstand higher temps and pressures and will last virtually forever! And if you ever had to replace a lower hose you'll appre...

Silicone heater hose, 42" for cars with the original heater valve bolted on the cylinder head.

Cars after 1976 require one of this 42" length and one C-GRH1006 39" length.

Cars from late 1984 to 1988 had 5/8" outlets on...

Radiator hose kit for all pre 1989 1275GT Clubman Minis where the top hose is slightly longer. This kit has top and bottom radiator hoses and 2 lengths of heater hoses…all in shiney red Silicone that should last forever and not degrade with heat, tim...

Radiator hose kit for all pre 1989 1275GT Clubman Minis where the top hose is slightly longer. This kit has top and bottom radiator hoses and 2 lengths of heater hoses…all in shiney black Silicone that should last forever and not degrade with heat, t...

Radiator hose kit for all pre 1989 1275cc Minis except clubman which has a longer top hose. the kit has top and bottom radiator hoses and two lengths of heater hoses(1m and 1.2m long)…all in shiney red Silicone. These should last forever and not degr...

Radiator hose kit for all pre 1989 1275cc Minis except clubman which has a longer top hose. the kit has top and bottom radiator hoses and two lengths of heater hoses(1m and 1.2m long)…all in shiney black Silicone. These should last forever and not de...

Made for small bore Mk2 minis except clubman these super flexible hoses are easier to fit than rubber and last so much longer. See C-GRH003 also for all 998 Clubman and original MK1 radiator with longer top hose which measures 7" long (c...

Made for small bore Mk2 minis except clubman these super flexible hoses are easier to fit than rubber and last so much longer. See C-GRH003 also for all 998 Clubman and original MK1 radiator with longer top hose which measures 7" long (c...