FAN BELT TENSIONER ON MPI
PQR10028

£20.99 exc vat

£25.19 inc vat

In stockIn stock
Tensioner wheel for the poly V fan belt fitted as standard on twin point injection cars.

£20.99 exc vat

£25.19 inc vat

In stockIn stock

Recommended usage 1 x PQR10028 to fit one mini.
Water Pump and thermostat from V134455 1275 MPI 96 - Qty 1

People also bought products

The original adjuster bolt is very expensive, this kit has been made in stainless steel for longevity and includes all 3 parts for adjusting the fanbelt tension on mpi cars at a fraction of the price of the OEM setup.

Engine mount bolt kit for manual cars, 1 kit requried per car.

Victor Reinz/Mahle small bore head gasket for A-series engines.



Gasket fitment. Writing side up.

Timing cover front plate and tensioner plate bolt and washer kit. Comes with all parts to fit the cover except for the counter sunk screws if fitting a duplex kit (our duplex kits all come with these).

This is the large seal for the early type oil filter assembly pre spin on type.

Genuine Bosch lambda sensor, fitted to both the twin and single point injection cars and fitted in the same exhaust manifold shared by both cars. Be warned the cheaper non branded sensors cause lots of issues hence we only sell the Bosch version.

Fitting kit comprising of studs, nuts, plain washers, spring washers and a gasket

You should replace the camshaft bearings every time the block goes to the machine shop. These bearings fit all late model 1275cc blocks (the ones without tappet covers on the back) It's almost too simple and thus often overlooked during a rebuild. Ca...

ARP Head stud kit that compromises of;

4 x Long Head Studs

7 x Short Head Studs (Disregard 2 if you're using a 9 stud application)

11 x Multipoint ARP nuts

11 x Heavy Duty Washers

4 x Rocker post studs <...

Mini Spares best quality complete gasket and seal kit for engine block and gearbox,for all common engine types and sizes.



Also comes complete with Mini Spares Evolution clutch oil seal 13H2934MS, differential oil seals...

ACL Race Bearings



ACL Race series bearings are precision manufactured to a wall thickness of ±0.0040mm giving engine builders close control of vertical oil clearance.

What is the purpose of ACL Race series bearings?
...

ACL Race Bearings



ACL Race series bearings are precision manufactured to a wall thickness of ±0.0040mm giving engine builders close control of vertical oil clearance.

What is the purpose of ACL Race series bearings?
...

Parts required to stop timing chain rattle on A plus engine using special anti stretch single row chain 3H2127EVO.Last chance to buy with the plate and pin to hold the tensioner as they are obsolete from Rover.

Fitted to 998/110...

Set of 4 ignition leads from the original supplier to Unipart, suitbale for all twin point minis 1997 onwards

MPI only. 3 YEAR GUARANTEE-UK made.Large impeller higher capacity water pump. Mini Spares procured product as original Rover Airtex tooling has been scrapped.

Fitted with a PPS, glass filled plastic impeller as used by Jaguar and Aston Marti...

3 YEAR GUARANTEE-UK made.Large impeller higher capacity water pump with top quality die cast body . Mini Spares procured product as the original superb Rover Airtex tooling has been scrapped.

Fitted with a PPS, glass filled plastic impeller...

3 YEAR GUARANTEE-UK made. Large impeller higher capacity water pump with a high quality die cast body. A Mini Spares procured product as the original superb Rover Airtex tooling has been scrapped.

Fitted with a PPS, glass filled plastic impe...

Negative earth A Plus 59D for any 1275cc with vac unit with modern day driving curves and petrol avaiable.

For best performance and tune we advise our electronic evolution version C-27H7701

Distributors can 'work' lon...

Ultra light non-adjustable steel duplex timing gear and chain set with locktab and countersunk screws but with a 2H4905EVO limited stretch race quality chain.

If you are working on your engine and you want to do it right then yo...