FRONT PANEL LATE RUBBER MOUNTED 1976-1997
MS4L

($82.50) £82.50 exc vat

($99.00) £99.00 inc vat

In stockIn stock
This late front panel will fit any Mini, with rubber mounted subframes, manufactured after 1976. It is probably easier to replace the entire panel than to repair a damaged one, especially if it's been hit more than once. Early Minis can use MS4L by also ordering 2 front subframe mounts, part number 21A2624.

($82.50) £82.50 exc vat

($99.00) £99.00 inc vat

In stockIn stock

Recommended usage 1 x MS4L to fit one mini.
Saloon and Front Ends - Qty 1

Alternative products

For 1990on and single point injection cars with 2 spotlamp holes and for AFU3389 sidelamps held on by 2 screws. See ASJ360070 for twin point cars with 4 spots and different bonnet locking position.

This late front (nose) panel will fit any Mini, with rubber mounted subframes, manufactured after 1976. It is probably easier to replace the entire panel than to repair a damaged one, especially if it's been hit more than once! Early Minis can use [l...

People also bought products

Small bracket under the front bumper lip to hold the number plate, sold singly.

ADAPTOR PANEL TO CONVERT LATER FRONT PANELS TO THE PRE 1964 FULL SKIRT FRONT PANEL.

ADAPTOR PANEL TO CONVERT LATER FRONT PANELS TO THE PRE 1964 FULL SKIRT FRONT PANEL.

Slat type front grille section for mini van which will need trimming before welding into recess of either an original damaged front panel or a saloon version.

It is sold as a grille size panel and can be fitted as such when painted with [li...

L/H Inner hinge type A post repair panel with hinge fitting holes mini, MK3

this is a genuine heritage part.

R/H Inner hinge type A post repair panel with hinge fitting holes mini, MK3

this is a genuine heritage part.

This Non genuine pattern panel has the holes for windscreen wipers and jets with barely an inch of pillar.

On cars from 1992/3 on check the original windscreen drain channel as the VIN numbers were stamped above the clutch master cylinder-wi...

Reproduction version os ASJ360070. For the twin point only as it changed shape to accommodate the front mounted radiator and different bonnet fittings.

This is the crossmember for the dash at the back of the engine bay which holds the master cylinders. When fitting to Clubmans extra end pieces are required. Fits 1976 on but does not have PDWA valve bracket. The original Rover parts are supplied with...

For vehicles with external hinges and sliding type windows this is a full inner front wing with the wheel arch panel. The panel is what that the outer A panels for the hinges attach to.This is the left hand pane wing with radiator vent slats but not ...

For vehicles with external hinges and sliding type windows this is a full inner front wing with the wheel arch panel. The panel is what that the outer A panels for the hinges attach to. This is the right hand panel made by Heritage but not 100% perfe...

Commercial Mini floor extension

It is an essential part for the correct restoration of all the longer wheelbase mini derivatives. From the original tooling.

The only bonnet landing panel available for the clubman shape body for a long time this part is perfect in every detail and was used on the heritage bodyshells.

A Genuine panel is now available from BL Heritage CZH149.

...

Aftermarket version of the L/H floorpan for 1991 on cars.

This floor was made stronger with smaller heel pad area to prevent vibration and rust and will fit any Rod change gear shift mini but was introduced on the first injection cars in 199...

A non genuine panel made for repairing the corner of the windscreen panel which is prone to rust from water splashing up from underneath the front wheel arch.

Experience has shown its easier to fit the genuine panel HMP441001 al...

You can spend hours cutting out rust and patching holes, but why bother? These reproduction floor pans extend the full width with vertical flanges for easy installation and fairly well represent the original stamping. They have added metal to include...

Inner front L/H wing with the A panel and door stiffener check strap panel attached for ease of fitment and alignment.This has the large round hole for the fan as fitted from 1991on

This early front (nose) panel will fit any Mini manufactured before 1976. It is probably easier to replace the entire panel than to repair a damaged one, especially if it's been hit more than once! Later Minis with rubber mounted subframes, use panel...

You can spend hours cutting out rust and patching holes, but why bother? These reproduction floor pans extend the full width with vertical flanges for easy installation, and fairly well represent the original stamping. They have added metal to includ...

1970 on, cars with internal hinges and wind up windows

This repair panel has holes for the hinges on A post and overlaps 3.5"(85mm)onto the wheel arch section of inner wing