£40.50 exc vat
£48.60 inc vat
In stock
£40.50 exc vat
£48.60 inc vat
In stockRecommended usage 1 x GCP90832AF to fit one mini.
If your late model Mini has a short (3" or so) clutch arm, you have a "Verto" clutch. This is your release (throw-out) bearing. Retaining o ring is AAU2866.
Performance clutch plate for road and rally Verto type - see also 20% upgraded pressure plate
Verto race quality tuftrided clutch arm kit made in EN24T for any heavy duty diaphragm- special design plunger with arm to suit, hardened clevis pin and R-clip included.
Non Genuine 3 piece Injection Clutch with the larger 190mm wide for 1990 on and all injection cars, but it can be used on earlier non injection Verto type engines only if the flywheel is 100% PERFECT WITHOUT WEAR. Check nothing fouls when bolting up ...
Upgraded Centre boss for all verto clutch/flywheel.
Fixing bolts are DAM5920 which are supplied in many clutch kits.
Clutch housing bolt to engine long 5/16" UNF 1.75" long with tuflock patch to secure. Earlier bolts less tuflock are {link]BH605141{/link}
3 piece Verto Clutch kit for Turbo with 180mm plate which can be used on any Verto flywheel including injected cars. Approximately 20% upgrade over standard this is ideal for any tuning mods to any Verto flywheel but cars from 1990 were fitted with a...
Performance clutch plate for road and rally Verto type - see also 20% upgraded pressure plate
This Verto type clutch arm is 2.75" long from the clevis pin hole.The earlier type pre verto is over 6"(165mm)long. the ball wears on both types and if the clutch is wrongly adjusted the arm (mainly the long type) can bend by way of hydraulic pressur...
Ring gear for all cars fitted with the pre-engaged starter on Verto flywheels from about 1984 on.
For pre injection Verto clutch cars with pre engaged starter, it is also designed to increase clamping
pressure which effectively upgrades the actual performance of the verto clutch, which with the AP pressure GCC679 (part of G...
When the verto clutch was introduced the factory started fitting this plastic protector over the clutch oil seal on Metro's. It then apeared on injection minis with LUF10005 clutch seal to the end of production. Should be replaced when s...
3 piece Borg and Beck Injection Clutch with the larger 190mm wide for 1990 on and all injection cars, but it can be used on earlier non injection Verto type engines only if the flywheel is 100% PERFECT WITHOUT WEAR. Check nothing fouls when bolting u...
If your 1982 on model Mini has a short (3" or so) clutch arm, you have a "Verto" clutch. This is your clutch plate disc if it is 180mm wide. If your car is 1990 or later you have a 190mm wide GCP90832AF plate. Thickness 7.69mm.
If your late model Mini has a short (3" or so) clutch arm, you have a "Verto" clutch. This is your release (throw-out) bearing. Retaining o ring is AAU2866.
Sleeve that covers the flywheel bolt on verto clutches for the release bearing
Note--early 58mm internal diameter sleeves had a plastic anti rattle sleeve which is no longer available but this later type is smaller in diameter and therefore ...
3 piece Borg and Beck kit, has a 180mm wide clutch plate,pressure plate and release bearing,fits all cars pre 1990 VERTO assemblies until fitment of 1275cc engines.
From 1990 on the clutch plate was increased to 190mm, for 1275cc which is ...
This is the only aftermarket copy of the GSY118 available and have been sold by us for many years without any problems. We always recommend genuine but the choice is yours. I would stick to the original from AP lockheed if keeping the ca...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.