£1.80 exc vat
£2.16 inc vat
In stock
2 per door are required and these are only for cars with external hinges that had the material check strap as per MK1/2 and vans.
£1.80 exc vat
£2.16 inc vat
In stockRecommended usage 4 x 14A764 to fit one mini.
Screw for either end of the material check strap on MK1/2/van/pickup minis with external hinges. The head of this screw is chromed for a superior finish.
The larger check strap bracket on the body that has a curved section. Shown as black in the picture. One per door required.
The door stiffener plate for the check strap on mk1/2 doors with external hinges
one per door required.
This stainless steel plate has recessed holes in for the check strap screws.
2 per door are required and these are only for cars with external hinges that had the material check strap as per MK1.2 and vans
Complete fitting kit for the door check straps on all Minis fitted with external hinges.
Complete fitting kit for the door check straps on all Minis fitted with external hinges.
Angled spacer washer for Mk1/2 external door hinge cars for the upper hinge
This screw can used to hold together the 2 halves of the disc shields on all
mini front discs. fits MK1/2 door escutcheons.
Use SE910161 and cut down to 3/8" long including head
PMZ306 was originally 3/8"long u...
Full Mk2 door handle set with 2 front door locking handles and boot handle with matching keys. Fitted from 1966 with the intoduction of the door safety escutcheon boss. This boss is available as 24A1834 and gasket 24A1835.
Regre...
Twin point injection cars had a split seal system door frame seal for the front doors,the lower acting as a shield cover for the trim, fitted from chassis no BD134455 ON
Some customers have replaced it by the one piece CGA2835MS<...
Twin point injection cars had a split seal system door frame seal for the front doors,the lower acting as a shield cover for the trim. fitted from chassis no BD134455 ON
Some customers have replaced it by the one piece CGA2835MS<...
Special lower seal--fitted to MPI cars from October 1996 show cars chassis no BD134455 ON
Has a lip on inner edge to hold carpet back and tidy internal trim but other than that the CGA2835MS will fit --the full set is
Special lower seal--fitted to MPI cars from October 1996 show cars chassis no BD134455 ON
Has a lip on inner edge to hold carpet back and tidy internal trim but other than that the CGA2835MS will fit --the full set is
The rubber that sits in the frame to hold the windows on wind up window type doors. The frames are ALA5746/7 or see MSSK2105 also used on Clubman Estate and Traveller rear windows in the finger pull grips.
Sold individually.2 pe...
Genuine Mini Spares mouldings product as supplied to Rover.
These are the later door mouldings that prevent water running down the windows into the door causing rust and have the black platic ends fitted for later car safety regulations but ...
Sliding window type weatherstrip kit R/H
kit contains lower and upper sliding channels plus the vertical strip that attaches to the glass as a draught excluder plus the stainless steel window catch runner that the lower channel sits in,with ...
The Cooper S had these mouldings and this is the same item but made for the MK3 wind up window cars. These are easy to install, drill 1/8" holes evenly spaced on the straight edges,3 each side and 4 at the top(not on any corners)of the window frame.T...
Sponge type seal on L/H A post of all minis with wind up window type doors to protect from water running down into body. A part you must keep your eye on to stop rust.
Sponge type seal on R/H A post of all minis with wind up window type doors to protect from water running down into body. A part you must keep your eye on to stop rust, if the sponge is gettig hard then replace it.
Moulded shape type right hand door stay grommet fitted until 1985 when it was replaced by a flat sponge type seal CGE10038/9.
Holds the window regulator to the door on wind up window minis from 1970 on.
Also holds fog lamp bracket to rear valance. 1/4" unf with 1/2" thread on
panhead type screw.
Genuine MK3 wind-up window upper slide up and down felt lined channel that fits into the R/H upper door frame. Left (PAM3077) and right (PAM3076) look identical but are mirror images.
Genuine MK3 wind-up window upper slide up and down felt lined channel that fits into the upper door frame. Left (PAM3077) and right (PAM3076) look identical but are mirror images.If you are looking for a cheaper budget version see PAM3077MS
...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.