£2.70 exc vat
£3.24 inc vat
In stock
£2.70 exc vat
£3.24 inc vat
In stockRecommended usage 2 x 14A6745 to fit one mini.
Screw for either end of the material check strap on MK1/2/van/pickup minis with external hinges. The head of this screw is chromed for a superior finish.
This plate has recessed holes in for the check strap screws.
2 per door are required and these are only for cars with external hinges that had the material check strap as per MK1/2 and vans.
The door stiffener plate for the check strap on mk1/2 doors with external hinges
one per door required.
Complete fitting kit for the door check straps on all Minis fitted with external hinges.
Upper door moulding rivet for Cooper S door trim. For Mk1 usually 1 at front and 3 at back making 4 per side and on Mk2 there were 2 per end at bottom making 4 per side. This is the 10mm head rivet and not required on our own 14A9773/9774 trims that ...
High quality non genuine door check strap for MK3 cars with wind up window doors (use with retaining pin CLZ412). Beware there are cheap copies on the market that are poor quality and when fitted to our cars did not function correctly!
The gasket that sits behind the door stiker on all wind up window type minis
on the B post.
Complete fitting kit for the door check straps on all Minis fitted with external hinges.
Angled spacer washer for Mk1/2 external door hinge cars for the upper hinge
MK3 door hinge fitting kit for all internal hinged doors. (hinges not included)
Special thread cutting screw 1/4 UNF 1.25" (31mm) long.
Screw to hold the lock assembly on the door of MK3 cars with internal hinges and wind up windows. On new doors or for easy fitment use these special screws with cutting thread (3 sided ...
SPECIAL 6/32" UNC COUNTERSUNK POZI SCREW 1/4" LONG FOR HOLDING THE 14A6835 BUFFER PLATE TO BODY.
This screw can used to hold together the 2 halves of the disc shields on all
mini front discs. fits MK1/2 door escutcheons.
Use SE910161 and cut down to 3/8" long including head
PMZ306 was originally 3/8"long u...
Full Mk2 door handle set with 2 front door locking handles and boot handle with matching keys. Fitted from 1966 with the intoduction of the door safety escutcheon boss. This boss is available as 24A1834 and gasket 24A1835.
Regre...
New set of metric studs, bolts, nuts and washers as supplied with the alloy external hinge kit (PEASE NOTE: This kit is NOT suitable for the original hinges). The studs have allen key socket ends to help put them into the hinge easily without damage,...
Twin point injection cars had a split seal system door frame seal for the front doors,the lower acting as a shield cover for the trim. fitted from chassis no BD134455 ON
Some customers have replaced it by the one piece CGA2835MS<...
Special lower seal--fitted to MPI cars from October 1996 show cars chassis no BD134455 ON
Has a lip on inner edge to hold carpet back and tidy internal trim but other than that the CGA2835MS will fit --the full set is
Special lower seal--fitted to MPI cars from October 1996 show cars chassis no BD134455 ON
Has a lip on inner edge to hold carpet back and tidy internal trim but other than that the CGA2835MS will fit --the full set is
The rubber that sits in the frame to hold the windows on wind up window type doors. The frames are ALA5746/7 or see MSSK2105 also used on Clubman Estate and Traveller rear windows in the finger pull grips.
Sold individually.2 pe...
4 Non Genuine door hinges as a car set for wind up window type doors from 1970 on. These are a top quality item as opposed to the cheaper junk version available on the market.
Sold seperately as
top right CZH202MS 1 r...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.