OVERRIDER FRONT L/H 96 ON 0N WHEN 4 SPOTLAMPS FITT...
14A9926

£17.92 exc vat

£21.50 inc vat

In stockIn stock
These different overriders have special shorter bars to fit on the front only of Rover minis which have 4 spotlamps fitted. MADE IN STAINLESS STEEL AS PER ALL OUR OVERRIDERS AND CORNER BARS see 14A9925 also.

£17.92 exc vat

£21.50 inc vat

In stockIn stock

Recommended usage 2 x 14A9926 to fit one mini.
Bumpers and Number Plates - Qty 2

Recommended products

Car set of fixings to hold on the Deluxe type overiders and corner bars, complete with sealing rubber to bumper and spacers.

If you have standard overiders see kit MSSK011.

These different overriders have special shorter bars to fit on the front only of Rover minis which have 4 spotlamps fitted. MADE IN STAINLESS STEEL AS PER ALL OUR OVERRIDERS AND CORNER BARS. See 14A9926 also.

Kit products

Specially designed for twin point injection cars. This kit has the 2 overiders and corner bars plus a stainless steel bumper with the pre stamped hole, plus fixings, for cars with 4 front driving lamps as fitted by Rover from 1997 on. Owing to the 4 ...

Mini Spares Stainless Steel Over Rider and corner bar kit for the front and rear of all 1997 on Minis with 4 driving lamps. This has shorter front corners bars than the original MK1 set, to allow for the extra 2 lamps fitted on MPI cars.

Com...

This kit has 2 special overiders and 2 slightly shorter corner bars

for fitting to cars with 4 driving lamps when fitted as original equipment by the factory on all Twin point injection cars. This special kit was designed by Keith Dodd for ...

People also bought products

An aftermarket version of the mini bumper in stainless steel it has the original type open ends (Rover curled the sharp edges over) - BUMPER BOLTS ARE FITTED BUT NO NUTS -3 required metric M6 thread nuts FS106047

For top qualit...

Bolt for the overider to lock plate at the back of the overider to secure it against the bumper.

Also has been used for the rear subframe trunnion 2A5819/21A2558.

Also used for the short water pump bolt.

This kit has 2 special overiders and 2 slightly shorter corner bars

for fitting to cars with 4 driving lamps when fitted as original equipment by the factory on all Twin point injection cars. This special kit was designed by Keith Dodd for ...

Made in stainless steel to the original shape because the metal chromed variety suffer badly from rust and tarnish owing to their position on the car, even these should be cleaned regularly to keep appearances up and for longevity.

Black ver...

Some bumpers have studs, some require bolts, this is the bolt.

This plate mounts on the back of the bumper for the overrider bolt to tighten up against to secure the overrider to the bumper on all minis fitted with any overriders except clubman specials.

Mini Spares Stainless Steel Over Rider and corner bar kit for the front and rear of all 1997 on Minis with 4 driving lamps. This has shorter front corners bars than the original MK1 set, to allow for the extra 2 lamps fitted on MPI cars.

Com...

Original genuine shape overrider corner bars, originally fitted to deluxe Mk1 minis and Cooper variants. Now made in stainless steel for longevity they have found their way onto many later minis. This one fits the left hand rear.

Overseas co...

Original genuine shape, fitted to all the MK1 deluxe cars and Coopers these overriders are now made in stainless steel to prolong life. They have pre drilled recessed holes to accept stainless steel corner bars unlike overseas copies.

These...

Original genuine shape overrider corner bars-originally fitted to deluxe Mk1 minis and Cooper variants. Now made in stainless steel for longevity they have found their way onto many later minis. This one fits the right hand rear.

Overseas co...

Genuine Mini Spares manufactured bumper from our own tooling that fits perfectly as per original ROVER bumpers. Better than the last genuine bumpers produced for Rover which is why we laid down tooling - BEWARE - most others available in stainless ar...

Original genuine shape, fitted to all the MK1 deluxe cars and Coopers these overriders are now made in stainless steel to prolong life. They have pre drilled recessed holes to accept stainless steel corner bars unlike overseas copies.

These...

When fitting bumper corner bars as per the old deluxe and Cooper S models you require this special angled spacer to fit under the bumper to give the bolt holding the corner bar a level seating platform.

Also known as the overrider corner bars-originally fitted to deluxe Mk1 minis and Cooper variants. Now made in stainless steel for longevity they have found their way onto many later minis. This one fits the right hand front. For twin point cars a sh...

1 metre will do a car set of overiders (32" 0R 815mm actually needed). Each piece was originally cut to 3" (6" per overider). Some people have also used this for fibre glass wheel arch to body seal for neatness such as w&p arches.

These different overriders have special shorter bars to fit on the front only of Rover minis which have 4 spotlamps fitted. MADE IN STAINLESS STEEL AS PER ALL OUR OVERRIDERS AND CORNER BARS. See 14A9926 also.

These corner bars were made shorter than the originals to accept the 4 lamps as fitted to the Twin point sportspack cars from 1996 on and also need different overriders 14A9925 & [link}14A9926[/link]. Also see MSSK027 kit.

Stainless steel with corner bar holes.

Any Mini with "corner bars" on the bumpers was probably considered a Deluxe model such as a Cooper S. If you want to restore your Deluxe or upgrade your standard you need these stainless steel bumpers w...

Also known as the overrider corner bars, originally fitted to deluxe Mk1 minis and Cooper variants. Now made in stainless steel for longevity they have found their way onto many later minis. This one fits the left hand front. For twin point cars a sh...