IDLER GEAR SHIM .134/5"WHITE
22A1547

£13.50 exc vat

£16.20 inc vat

In stockIn stock
Idler gear shims for the Pre A Plus gearboxes with 0.750" (19mm) size shafts

Quantity required per gearbox is 2 but idler gear shims require shimming for correct clearance 3-6 thou as per workshop manuals but 3 thou for road and 4 thou for race is found to be reliable, see following

22A1545 130-131"

22A1546 132-133"

22A1547 134-135"

22A1548 136-137"

22A1549 138-139"

£13.50 exc vat

£16.20 inc vat

In stockIn stock

Recommended usage 1 x 22A1547 to fit one mini.
A Type Gears - Qty 1
4 Synchro Gears Up to 1979 with 14MM Nose Mainsha - Qty 2

Recommended products

Bearing 26.9mm wide to take 19.05mm idler gear shaft that fits in the gearbox case and clutch housing case on 4 synchro gearboxes until introduction of A plus when a larger bearing was fitted.

Alternative products

Idler gear shims for the Pre A Plus gearboxes with 0.750" (19mm) size shafts.

Quantity required per gearbox is 2 but idler gear shims require shimming for correct clearance 3-6 thou as per workshop manuals but 3 thou for road and 4 thou for ...

Idler gear shims for the Pre A Plus gearboxes with 0.750" (19mm) size shafts

Quantity required per gearbox is 2 but idler gear shims require shimming for correct clearance 3-6 thou as per workshop manuals but 3 thou for road and 4 thou for r...

People also bought products

These are the later A+ type spec which rover superseded to when upgrading the idler gear material on injection cars. See workshop manual for shimming details

Quantity required is 2 per gearbox but the idler gear requires shimming for correct...

The shims go against the mainshaft double roller bearing securing cap in your gearbox to give it pre load. See workshop manual for advice but you are aiming for only 1 thou pre load.

These are the later A+ type spec which rover superseded to when upgrading the idler gear material on injection cars. See workshop manual for shimming details.

The idler gear in all Mini power units must be set with great care. The thrust wa...

Idler gear shims for the Pre A Plus gearboxes with 0.750" (19mm) size shafts

Quantity required per gearbox is 2 but idler gear shims require shimming for correct clearance 3-6 thou as per workshop manuals but 3 thou for road and 4 thou for r...

The bronze washer for the planet gears in the differential for pre A plus gearbxes. You can use the DAM5071 and cut the lips off.

Idler gear shims for the Pre A Plus gearboxes with 0.750" (19mm) size shafts.

Quantity required per gearbox is 2 but idler gear shims require shimming for correct clearance 3-6 thou as per workshop manuals but 3 thou for road and 4 thou for ...

Idler gear shims for the Pre A Plus gearboxes with 0.750" (19mm) size shafts

Quantity required per gearbox is 2 but idler gear shims require shimming for correct clearance 3-6 thou as per workshop manuals but 3 thou for road and 4 thou for r...

These are the later A+ type spec which rover superseded to when upgrading the idler gear material on injection cars.see workshop manual for shimming details.

Quantity required per gearbox is 2 but idler gear requires shimming for correct cle...

smaller of the 2 shims at the ends of the laygear on the layshaft. These are sized accordingly and fit the first gear end --See DAM3180/1/3 for alternative sizes

You will need to shim up your diff bearings with these washers as required. See workshop manuals for details. See also DAM3109 & DAM3633.

This kit contains 1 each of 3 alternative sizes plus 2 of the standard size shim

for shimming idler gear on A Plus idler gears. These are the later type spec

which rover superseded to when upgrading the idler gear material on inject...

Idler gear shims for the Pre A Plus gearboxes with 0.750"(19mm) size shafts

Quantity required per gearbox is 2 but idler gear shims require shimming for correct clearance 3-6 thou as per workshop manuals but 3 thou for road and 4 thou for ra...

2 thou shims to go against the mainshaft double roller bearing securing cap in your gearbox to give it pre load. See workshop manual for advice but you are aiming for only 1 thou pre load--these were sold by Unipart as 3 thou but the Rover drawing we...

These are the later A+ type spec which rover superseded to when upgrading the idler gear material on injection cars. See the idler gear in all Mini power units must be set with great care. The thrust washer comes in various thickness to allow for acc...

See DAM3108 also for smaller diff shims. Refer to workshop manual for fitment.

Primary gear thrust washers are made in varying sizes to take up the play.

Standard gap size should be between 3-6 thou. See DAM6486, DAM6487, DAM6488, DAM6490, DAM6492 for alt...

Laygear thrust washer on 4th gear end which is one size only. The first gear end is the adjustable laygear washer end but these are obsolete on Pre A plus layshafts. This one fits all 4 synchro gearboxes.

Primary gear thrust washers are made in varying sizes to take up the play.

Standard gap size should be between 3-6 thou. These are for the 850/998/1098cc

engines with 22A1493 Deva bush primary gear. Early 850cc had thin...