£2.00 exc vat
£2.40 inc vat
In stock
£2.00 exc vat
£2.40 inc vat
In stockRecommended usage 1 x 2A3624MS to fit one mini.
Left hand differential lock tab as used on rod change boxes up until 1982 when they were not longer used. For R/H locktab see 22A962
Right hand differential lock tab as used on rod change boxes up until 1982 when they were not longer used.
FITTED from 1984 on-single locktab for the 3 bolt main bearing(double roller)
housing and deleted 1996 on.locking glue used such as locktite
3 of these bolt are used on the speedo housing gearbox front cover-they used to be 53K1474 studs 3.75" long but change to this bolt in 1985 3.25"long 5/16"unc
with tuflock patch to secure.
These are the later A+ type spec which rover superseded to when upgrading the idler gear material on injection cars. See workshop manual for shimming details
Quantity required is 2 per gearbox but the idler gear requires shimming for correct...
The shims go against the mainshaft double roller bearing securing cap in your gearbox to give it pre load. See workshop manual for advice but you are aiming for only 1 thou pre load.
These are the later A+ type spec which rover superseded to when upgrading the idler gear material on injection cars. See workshop manual for shimming details.
The idler gear in all Mini power units must be set with great care. The thrust wa...
Genuine 1ST Motion shaft SINGLE track original bearing for 4 synchromesh 1st motion shaft.
This is a Genuine RHP bearing, and should not be confused with cheap alternatives. The cheap aftermarket bearings often fail and the work involved to...
Genuine RHP as originally fitted to every production Mini.
Two of these main diff carrying bearings are required in the gearbox and this new steel caged type fits either way round. Should be pre loaded by 1-2 thou.
Some original fi...
The bronze bush in the differential housing that the gear change selector rod sits through which should be lightly greased.
Idler gear shims for the Pre A Plus gearboxes with 0.750" (19mm) size shafts
Quantity required per gearbox is 2 but idler gear shims require shimming for correct clearance 3-6 thou as per workshop manuals but 3 thou for road and 4 thou for r...
Minispares were the first company to produce these layshafts for performance engine/gearboxes as the standard type would flex and resullt in the breakage of the bearings causing seizure.Produced in standard material heat treated to the correct core d...
Bearing 26.9mm wide to take 19.05mm idler gear shaft that fits in the gearbox case and clutch housing case on 4 synchro gearboxes until introduction of A plus when a larger bearing was fitted.
Genuine new 6 tooth speedo drive spindle that mated with 17 tooth speed pinion 22A1881 on cars with 10" wheels before 1980 plus any year 1275GT. Also 12"wheel cars with 3.44 final drive 1984 on. On the Metro mini this was used with 17 an...
Genuine RHP bearings. Not cheap Imported rubbish as sold under this part number.
This is the workhorse of the Mini gearbox. This double roller bearing supports the shaft where it transmits the power to the wheels. When this bearing goes, the...
This is the top hat bush for all primary gears and is now silicon based to help lubrication of this dry running bush. Used in all our primary gears.
For Cooper S or pre A plus 1275 type primary gears we also have a a replacement front bush i...
Pre A plus 4 synchro laygears had 2 of these fitted plus a small bearing whereas the A plus laygear had only one.
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.