£1.76 exc vat
£2.11 inc vat
In stock
Originally a twin spring design 17H8184/5 Leyland/Rover converted to a single spring.
For single leading front shoe with one wheel cylinder per drum 1959-64 use GBK1834
£1.76 exc vat
£2.11 inc vat
In stockRecommended usage 4 x AAU8243 to fit one mini.
If you have original drum brakes on the front of your mini with twin leading shoes (2 cylinders per drum) this is the kit of 4 tension springs you should change. Originally a double spring type they are now single spring coil per item but more effici...
If you have original drum brakes on the front of your mini with twin leading shoes (2 cylinders per drum) this is the kit of 4 tension springs you should change. Originally a double spring type they are now single spring coil per item but more effici...
EBC Blue Stuff pads are the endurance-grade, longest lasting material. Blue Stuff pads have a slightly lower friction coefficient than their counterparts; Green Stuff, Yellow Stuff and Red Stuff, but delivers far longer life.
Blue ...
Genuine Mini Spares R/H caliper for 8.4" disc set ups remanufactured exclusively for Minispares. Lots of alternatives on the market but AP no longer make the originals but as their largest agent for Mini these are our own and fully tested.
C...
Genuine mini Spares L/H caliper for 8.4" disc set ups remanufactured exclusively for Minispares. Lots of alternatives on the market but AP no longer make the originals but as their largest agent for Mini these are our own and fully tested.Caliper fit...
Pair of vented discs and Mintex GBP258AF pads,one of our best selling brake disc kits. Includes discs[link](GBD496)/link] which are a bargain.Only for carss fitted with vented discs already.
This is not a direct replacement kit ...
If your rear brake drums have 1" built in spacers such as all Cooper S and any post 1984 minis, these are the longer drum retaining screws, 2 required per drum and sold individually.
Suitable for standard 8.4" / 7.5" /7" brake calipers. Also used for front wheel cylinders on twin leading shoe type drum brake cars. This is where you have 2 cylinders per hub as opposed to the early single leading type which had one cylinder only pe...
The screw that holds the drum on the hub. Earlier hubs had two screws, many replacements have only one, all that’s needed.
Split pin for the larger size CV joint as fitted to disc brakes. This pin is usually supplied in our normal stock bearing kits. Sold individually.
this will also fit the nut for the rubber cross drive coupling on the gearbox
Mintex brake shoes for the rear of all minis which are 1.25" wide. Also fitted to front on early single leading shoe cars (dry suspension pre 1964) with a single wheel cylinder. Manufactured by Mintex and sold as a box set of 4 brake shoes for one re...
Set of 4 Brake pads from the original manufacturer Delphi for the 8.4" wide disc fitted as standard to minis from 1984on with 2.920" pad width.
A set of split pins are available as GBK1010 or with metal retaining clips as [link]...
Genuine AP product as original.This strange looking coily spring holds the front brake shoes against the drum for better braking efficiency by holding them in a set position which also cuts out brake judder caused by sideways movement.
Fitte...
For those old original drum brakes on the front of a mini with 1.5" wide type fitted. Some pre 1964 dry suspension had the smaller rear type 1.25" wide fitted the same as the rear. After Unipart's demise our stock from Oct 1st will be Mintex as used ...
1.4mm thick copper washer for all clutch and brake joint uses. This washer is 17.4mm wide with an 11.4mm diameter hole. Larger than a 233220A.
Genuine Lockheed seal repair kit. Minis from 1984 on with 8.4" discs plus.
This rebuild kit also fits the Midget/Sprite 1098/1275cc front disc brake calipers. The kit includes all the large seals needed to do both pistons in one caliper exce...
Brake line from RH brake hose union to the LH brake hose. 44" in length.
Also master cyl to servo for L/H/D which was 43" long.
If you have original drum brakes on the front of your mini with twin leading shoes (2 cylinders per drum) this is the kit of 4 tension springs you should change. Originally a double spring type they are now single spring coil per item but more effici...
10" long pipe with 2 male ends used on front drum brakes to join the wheel cylinders. Made in easy bend copper for long life. These kits or pipes are at least 35% off retail.
Genuine AP car set of 4 brake hose for cars with front disc brakes. If you are changing one through wear and tear it is a good idea to change the whole set and save money with peace of mind about your brake system. Securing nuts included
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.