£52.50 exc vat
£63.00 inc vat
In stock
These are copies as the original base tooling by Lucas was scrapped.
Seperate parts if required are below:
Lens only is BAU1796
Seal to body 37H4189
Seal to lens 37H4190
£52.50 exc vat
£63.00 inc vat
In stockRecommended usage 1 x ADU3018 to fit one mini.
Wiper motor fitting kit to fit all mk2 onwards wiper motors to the bulkhead.
Pop rivet for fixing the headlamp bowl to the wing. Great for MS14 metal bowl but be careful if using on plastic bowls
This is the hazard switch repair plug for post 1976 rocker switches, pins supplied so you can wire accordingly.
Lots of things have been written about performance plug ignition wires but regardless of what you believe we all know that good wires are a must. This special competiton wires set from the Lucas factory has 8mm wire and the highest performance, no br...
Wiper Swithch MK1/2/EARLY MK3 blade type switch for using to convert to 2 speed wipers when current 2 speed wiper motor is used.
Plug and fly loom for later 2/3 clock speedos, useful if you are converting from a centre speedo to later clocks or just repairing a standard loom.
Negative earth only-45D electronic distributor with vac for 1275GT and any pre A Plus 1300cc engine including Sprite and Midget in line engines-
For best performance and tune we advise our electronic Evolution version C-27H7698<...
Negative earth A Plus 59D for any 1275cc with vac unit with modern day driving curves and petrol avaiable.
For best performance and tune we advise our electronic evolution version C-27H7701
Distributors can 'work' lon...
Gasket/seal for all 1997 on mpi headlamp bowls (self levelling type).
original Lucas type RESIN BASED CONDENSER made for the 45/59D type distributor if you want a quality item rather than the cheaper inferior parts available. Filled with 3m of winding inside as per original Lucas but every copy analysed to date has ...
Electronic Distributor for any standard A+ 998cc. Negative earth only.
From 1982on 998cc were fitted with a ballast coil which means a new wire must be fitted from fusebox top left terminal where there is a large white cable to the...
Coil bracket fitted to end stud of cylinder head,clutch end for coil to mount on as fitted 1969-94-MK3 on. This has been made to the original specification with the welded lug nuts rather than the cheaper method of having just plain holes to take a b...
Screw for holding PRC1230A to the number plate light body, 1970 onwards.
Plastic holder for the later flasher unit GFU2218. Needs to be mounted to the bulkhead prior to fitting the flasher unit to the holder
Screw for chrome metal number plate lamp on mk3 19790 on - You will have to drill the lens out to take M4 screw.
Stainless steel screw kit for all mk2/3 lens to lamp body. Comes as a car set with six screws and six fibre washers.
The half bowl for holding original sealed beams into the headlamp bowl om minis and many other headlamps of the 60s and 70s. Sold singly 2 required per car.
Best on the market, sports coil-Not Lucas. A standard coil can only do so much, and when compression is raised (as in most high performance engines) or improper fuel mixtures occur something better is needed. This sports gold coil with proven origina...
Originally fitted as standard to the MGB and MGB GT, but has the same plug configuration as the 76 on Mini's so can be used in place of the stabdard rocker switch
If you also have an issue with the plug, a new plug and wiring repair is avail...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.