BARE MPI BULKHEAD SKIN
AHA36008

£50.00 exc vat

£60.00 inc vat

In stockIn stock
BARE BULKHEAD SKIN



THIS IS THE LATER MPI PRESSING, BUT CAN BE CONVERTED TO SUIT EARLY CARS BY EITHER CUTTING ROTADIP HOLE YOURSELF, OR BY FITTING THE PRE FORMED HMP441017



A VERY CHEAP PANEL THAT CAN BE CUT TO MAK...

£50.00 exc vat

£60.00 inc vat

In stockIn stock

Recommended usage 1 x AHA36008 to fit one mini.

People also bought products
WINDSCREEN CORNER SUPPORT PANEL R/H
MS6XR

THIS NON GENUINE PANEL PROTECTS THE UNDERSIDE OF THE WINDSCREEN VALANCE UNDER THE FRONT WING SECTION RIGHT HAND. Also fitted on the inner wing panel 14A8346 & 14A8347.

£12.15 exc vat

£14.58 inc vat
REAR BACK PANEL LOWER HALF MK2 on
HMP441019

genuine rear lower back panel for MK2/3 on, which goes up as far as lower edge of backlight seal ridge

£240.00 exc vat

£288.00 inc vat

now

£216.00 exc vat

£259.20 inc vat
WINDSCREEN CORNER SUPPORT PANEL L/H
MS6XL

This non genuine panel protects the underside of the windscreen valance under the left hand front wing section. Also fitted on the inner wing panel 14A8346 & 14A8347.

£12.15 exc vat

£14.58 inc vat
FLOOR TO WHEEL ARCH BRACKET L/H
14A6610

rear subframe mounting stiffener L/H repair bracket with holes for subframe mounting and attaches to wheel arch Fits on ALA8623

£15.00 exc vat

£18.00 inc vat

now

£12.75 exc vat

£15.30 inc vat
WING INNER AND A PANEL R/H MK3 1970 ON
ABD36004

Inner front R/H wing with the A panel and door stiffener check strap panel attached for ease of fitment and alignment. Always check the bonnet prop bracket location as they changed.

£239.00 exc vat

£286.80 inc vat

now

£203.15 exc vat

£243.78 inc vat
REAR BACK PANEL LOWER REPAIR BELOW LIGHTS
HMP441009

Genuine repair panel which is about 2.52 high from bumper mounting seam and

includes hinge holes and lower part of bootlid surround channel. Full width panel for any saloon.

£215.00 exc vat

£258.00 inc vat

now

£193.50 exc vat

£232.20 inc vat
REAR VALANCE CLOSING/SUPPORTING BRACKET R/H
MS40R

Non genuine rear valance closing panel R/H for saloon cars only. Similar to ALA5528 but less panel with 2 holes for mounting rear subframe and 14A6609 floor to wheel arch reinforcement.

£14.40 exc vat

£17.28 inc vat
PANEL A POST/DOOR STEP REPAIR R/H WIND UP WINDOW T...
HMP441012

This panel is for wind up window type doors that have internal hinges and this contains the part of the front A post where the hinge and door stay holes are down to and including the door step and along and up the B post a few inches covering the mai...

£99.00 exc vat

£118.80 inc vat

now

£89.10 exc vat

£106.92 inc vat
BOOT FLOOR PANEL REAR SECTION ONLY ABOUT 10" DEEP
MS54

This 9.5" rear section of the boot (trunk) floor is ideal for collision or rust repair. Many times if you are hit from the rear the floor right in front of the bumper gets damaged-this will fix it. If rust is your problem, then this along with a new ...

£32.00 exc vat

£38.40 inc vat
WING TO A PANEL SUPPORT
14A7602

Small angled bracket fitted by factory to stiffen front wings to A panels

£2.30 exc vat

£2.76 inc vat
WING INNER VENTED AND A PANEL L/H 1969-91
ALA6279

This inner wing has the grille slats for the radiator cooling. Built into this panel also is the A panel and door stiffener check strap panel attached for ease of fitment and alignment for wind up window type doors 1969-89.

£239.00 exc vat

£286.80 inc vat

now

£203.15 exc vat

£243.78 inc vat
REAR VALANCE CLOSING/SUPPORTING BRACKET LH
MS40L

Non genuine rear valance closing panel L/H for saloon cars only,

similar to ALA8623 but less closing panel with 2 holes for mounting rear subframe and 14A6610 floor to wheel arch reinforcement.

£14.40 exc vat

£17.28 inc vat
TANK STRAP BRACKET REAR LH
CZH3241

Tank strap bracket welded to the rear of the boot floor which the single diagonal tank strap 21A2838 attaches to.

£7.35 exc vat

£8.82 inc vat

now

£5.95 exc vat

£7.14 inc vat
FLOOR PAN & XMEMBER FOR ROD CHANGE SALOON 1976-96
ADA36002E

The last type of rod change rib design floor made for the assembly line fits cars from 1973-96-It has a large rib down the centre of the L/H side

This floor produced from genuine tools has the crossmember fitted with the sill panels and ja...

£650.00 exc vat

£780.00 inc vat

now

£552.50 exc vat

£663.00 inc vat
SEAM VERTICAL FINISHER FRONT FITS BOTH SIDES
BMP127

Body Seam Covers. The seams of the Mini are designed to be covered. Both original and aftermarket strips are available and aftermarket Chromed Stainless steel version are also in stock for the very special Mini. 2 REQUIRED FOR 1 CAR

and sold...

£14.98 exc vat

£17.98 inc vat
SEAM FINISHER R/H REAR SEAM NOT PRIMED
BMP124MS

Quality Aftermarket Body Seam Covers. These are the vertical ones that protect the 4 corners of your cars body seams. Both original and Mini Spares own aftermarket strips are available plus a stainless steel version for that special Mini.

£5.45 exc vat

£6.54 inc vat
BOOTLID 1969 TO 1988 (uses 14A6584 SEAL)
BMP339

BOOT LID MK3 until '88 w/holes for seal retaining clips

£235.00 exc vat

£282.00 inc vat

now

£216.20 exc vat

£259.44 inc vat
SEAM MOULDING REAR ARCH TO SEAM 2" SALOON BODY
BMP129

Metal horizontal trim that fits between the rear of the rear wheel arch to the vertical seam.

£5.00 exc vat

£6.00 inc vat
SEAM FINISHER L/H REAR NOT PRIMED
BMP125MS

Quality Aftermarket Body Seam Covers. These are the vertical ones on each corner

of your car to cover and protect the body seams. Both original and Mini Spares own aftermarket strips are available and Minispares even manufacture them in Stai...

£5.45 exc vat

£6.54 inc vat
SEAM MOULDING CLIP STAINLESS STEEL
BMP128MS

These are the clips that hold on the vertical seam mouldings on all minis.

The original metal type are prone to rust so Mini spares producedd these stainless steel versions which are also cheaper. Supplied as a single clip, order as many as ...

£0.28 exc vat

£0.34 inc vat