UNDER FLOOR CLIP FOR FUEL AND BRAKE PIPE TAG TAB
ALA5536

£3.25 exc vat

£3.90 inc vat

In stockIn stock
Clip for underside of front floor(3 per side) 6 in total fitted to 90

£3.25 exc vat

£3.90 inc vat

In stockIn stock

Recommended usage 6 x ALA5536 to fit one mini.
Saloon Floor Panels - Qty 6

People also bought products

Clip on heelboard for pipes-2 fitted on all models until SPI 1991 onwards which had one onlyMS51heel board panel has 2 fitted and HMP441008 has one only.

Clip under front floor fitted to 1990 for holding fuel/ brake lines (2 per car)

located beside floor pan footwell and tunnel

Special clip for the lower brightwork moulding 14A8009 for finishing off the lower dash, crash pad rail, or on earlier cars the painted metal surface of the panel which holds the switch panel section.

The moulding 14A80...

This is the small plastic nut used to hold the fuel line protector shield on later cars, also used to hold the catalytic converter heat shield on, 4 required for each shield.

The scrivet for holding the front of the rear wheel Sportspack arch and the rear of the front arch. Rover also used rivet RY612535 as an alternative.

Plastic clip for sunvisor 1964-5 and some bonnet props on early cars,was GHF1120 and ADA4370. the side clip on these models was ADA4484.

this set up was used with first plastic mirrrors and black rubber...

Black bushes for wiper wheelboxes. Sold as a wiper wheel box set(one above the windscreen scuttle cowl and one under the cowl), takes two sets per car.

To fit early Mk1/2 cars cut down the part that fits under the panel work part(this part h...

One of the distinguishing features of the Cooper S model was the chrome trim around the door windows. If yours is missing or mangled, it can now be replaced

(we won't ask for your car's pedigree if you're adding it to a non S door)!

This is the bracket on the inner wing to put your bonnet prop into when the bonnet is in the open position.

These are the little 'whisker clips' that hold the 14A9907 bezel on the front of the oval 3-instrument gauge pod 24A2702. The 'ears' slot into the back of the bezel and the tails that stick out go thru one of 14 holes in the...

One of the distinguishing features of the Cooper S model was the chrome trim around the door windows. If yours is missing or mangled, it can now be replaced

(we won't ask for your car's pedigree if you're adding it to a non S door)! These fi...

These are the original Rover Xparts clips that hold on the vertical seam mouldings for all minis, prone to rust this was Rovers upgrade but Mini spares produced a stainless steel version BMP128MS which is also cheaper and a better option...

A favourite consumable goods item used for many purposes using no 10 screw, also fits early rad cowlings that use ARA1117 screws.

Also used for other trim areas this clip holds the vinyl or fabric of the seat covers to the metal framework.This part has larger D shape and claw spikes but if you want the smaller D shape and claws for headlining and rear seat covers see[link]14A80...

Your battery box 5L877 should be held in place by this rubber strap.

Moustache whisker clip for MK 1 grille. The end pieces of trim on the MK1 grille moulding known as the moustache. If your MKI whiskers have been gone so long that the clips and rivets are missing. Usually 3 per side fitted, clips sold individually.

clip that sits on the activating lever on the bottom of the MK3 door handle itself.

New door handles CZH886 and CZH887 have this clip on already.

This plastic clip was commonly used by Rover for all car trimming and first found its way on the wind up window version mini door panel.9 per side but always purchase a spare in case of breakages.

Heavy duty s/steel bonnet pin kit, contains a pair of pins and all the mounting hardware.