WING FRONT L/H WITH SIDE IND.NON GEN 1985-96
BMP455MS

£69.00 exc vat

£82.80 inc vat

In stockIn stock
These wings have the original round headlamp hole which is okay unless you have the dipping headlamps fitted to some export models and MPI cars--You will have to use the genuine wing if you have dipping headlamps.See BMP455 for cars with ariel hole and ASB360010 without ariel hole. cars registered after 1st april 1986 need side repeaters

£69.00 exc vat

£82.80 inc vat

In stockIn stock

Recommended usage 1 x BMP455MS to fit one mini.
Saloon and Front Ends - Qty 1

Recommended products

Small angled bracket fitted by factory to stiffen front wings to A panels

Alternative products

Fits all minis with side repeater lamps and an aerial hole from 1988 until 1996 except export models with adjusting headlamps. After 1997 ASB360010 should be used, which has no aerial hole, and a recess for the dipping headlight motor. ...

People also bought products

part inner wing L/H from Damper bracket mounting pointing forward for SPI modles 1991-96 with large round electric radiatore fan hole

NON genuine panel

part inner wing R/H from Damper bracket mounting points forward MK1 except Clubman. 1959-69 it has no air hole in side-see CZH3064 for later type with hose hole.

NON genuine panel

O/S/F wing t for 1996 on cars. THIS WING STILL NEEDS MODIFYING to allow for fitting of Sportspac arches and 13" wheels. After trimming/cutting to size remember to replace or renew the stiffener lip ALR360380

Has the headlamp re...

Part inner wing L/H from Damper bracket mounting points forward. MK1/2/3 except Clubman. This panel has radiator cooling slats as fitted to 1991

NON genuine panel only as part panel

part inner wing R/H from Damper bracket mounting points forward MK2/3 except Clubman. 1969-91 not Mk1/2 as it has air hole in side

NON genuine panel

If you fit 13" wheels and need to cut the wings away for clearance these are the reinforcements strips Rover used on the cars with Sportspack arches.

see Downloads on web site for diagrams on where to cut wings and A panels under part number...

Aftermarket wings do the job at a fraction of the cost of originals. This right front wing for the Mini will fit all MKI, II, III, IV. A slight difference exists between the early and the later models as to headlamp mounting holes. These reproduction...

Only this genuine wing is now available for the mini clubman but you will probably require the headlamp backing panel CZH120

Only this genuine wing is now available for the mini clubman but you will probably require the headlamp backing panel CZH121

1970 on, cars with internal hinges and wind up windows

This repair panel has holes for the hinges on A post and overlaps 3.5"(85mm)onto the wheel arch section of inner wing

1970 on, cars with internal hinges and wind up windows

This repair panel has holes for the hinges on A post and overlaps 3.5"(85mm)onto the wheel arch section

Inner l/h wing with large fan hole from 1991-96. This panel is available with the A panel fitted for ease of fitment as ABD36005

Was ABD36009 but that did not have the stiffener plate for the damper bracket fitted which was diff...

1970 on, cars with internal hinges and wind up windows

This repair R/H panel has holes for the hinges on A post and overlaps 6" at top tapering to 9" at bottom (150mm-215mm) onto the wheel arch section.

Also has the first section of...

1970 on, cars with internal hinges and wind up windows.

This L/H repair panel has holes for the hinges on A post and overlaps 6" at top tapering to 9" at bottom (150mm-215mm)onto the wheel arch section.

Also has the first section of...

Right hand inner wing section only for MK3 cars with 3 air vent holes. One with 4 bolt holes,one with 4 castellated bolt holes (nuts welded in place) and one large trunk hose hole at front. If you want the same panel with A panel combined for better ...

Aftermarket wings do the job at a fraction of the cost of the originals. This left front wing for the Mini will fit all MKI, II, III & IV. A slight difference exits between the early and the later models as to headlamp mounting holes. These reproduct...

These wings have the original round headlamp hole which is okay unless you have the dipping headlamps fitted to some export models and MPI cars--

1997-2000 cars need to use ASB360009 which has the recess for the headlamp adjusti...

Fits all minis with side repeater lamps and an aerial hole from 1988 until 1996 except export models with adjusting headlamps. After 1997 ASB360010 should be used, which has no aerial hole, and a recess for the dipping headlight motor. ...

Fits all minis with side repeater lamp from 1988 up until 1996 except export models with adjusting headlamps.

1997-2000 cars need to use ASB360009 which has the recess for the headlamp adjusting motor. cars registered after 1st...

Minis most used rubber plug 1.25" wide for holes approximately 7/8".

Fits floor, aerial hole and steering column extra hole and radius arm shroud on MK1/2 minis.These floor plugs vary in number from 11 in a Elf/Hornet,Mk1 and 1994 on cars do...