GENUINE MINI CLUBMAN WING R/H
CZH408

£155.00 exc vat

£186.00 inc vat

now

£139.50 exc vat

£167.40 inc vat

In stockIn stock
Only this genuine wing is now available for the mini clubman but you will probably require the headlamp backing panel CZH120

£155.00 exc vat

£186.00 inc vat

now

£139.50 exc vat

£167.40 inc vat

In stockIn stock

Recommended usage 1 x CZH408 to fit one mini.
Clubman Body Panels - Qty 1

Recommended products

genuine panel that holds the headlamp assembly on the mini clubman versions.

this is the right hand side

People also bought products

O/S/F wing t for 1996 on cars. THIS WING STILL NEEDS MODIFYING to allow for fitting of Sportspac arches and 13" wheels. After trimming/cutting to size remember to replace or renew the stiffener lip ALR360380

Has the headlamp re...

The full inner wing with wheel arch section for the mini clubman range --if you need only the first 20" approx of the inner wing see CZH3063.

If you fit 13" wheels and need to cut the wings away for clearance these are the reinforcements strips Rover used on the cars with Sportspack arches.

see Downloads on web site for diagrams on where to cut wings and A panels under part number...

Only this genuine wing is now available for the mini clubman but you will probably require the headlamp backing panel CZH121

1970 on, cars with internal hinges and wind up windows

This repair panel has holes for the hinges on A post and overlaps 3.5"(85mm)onto the wheel arch section of inner wing

1970 on, cars with internal hinges and wind up windows

This repair panel has holes for the hinges on A post and overlaps 3.5"(85mm)onto the wheel arch section

1970 on, cars with internal hinges and wind up windows

This repair R/H panel has holes for the hinges on A post and overlaps 6" at top tapering to 9" at bottom (150mm-215mm) onto the wheel arch section.

Also has the first section of...

1970 on, cars with internal hinges and wind up windows.

This L/H repair panel has holes for the hinges on A post and overlaps 6" at top tapering to 9" at bottom (150mm-215mm)onto the wheel arch section.

Also has the first section of...

Aftermarket wings do the job at a fraction of the cost of the originals. This left front wing for the Mini will fit all MKI, II, III & IV. A slight difference exits between the early and the later models as to headlamp mounting holes. These reproduct...

These wings have the original round headlamp hole which is okay unless you have the dipping headlamps fitted to some export models and MPI cars--

1997-2000 cars need to use ASB360009 which has the recess for the headlamp adjusti...

The section forward from the damper (shock absorber) bracket area

these sections approx 20" long often rust around the areas where they weld to the front wings.

Minis most used rubber plug 1.25" wide for holes approximately 7/8".

Fits floor, aerial hole and steering column extra hole and radius arm shroud on MK1/2 minis.These floor plugs vary in number from 11 in a Elf/Hornet,Mk1 and 1994 on cars do...

N/S/F wing without ariel hole which was standard fiment for 1996 on cars which had a factory fitted roof ariel. THIS WING STILL NEEDS MODIFYING to allow for fitting of Sportspac arches and 13" wheels. After trimming/cutting to size remember to replac...

The Heritage produced front wings (fenders) for the Mini are the original with

correct round hole for headlamp. They fit. The proper gauge metal and original tooling ensures that even the novice body man can make them work great. Cars regist...

This panel is available separately but is fitted on all mini wings. It is required quite often however when fitting a new wing on the ADO16 old 1100 and 1300 cars

The Heritage produced front wings for the Mini have the correct headlamp round hole. They fit! The proper gauge metal and original tooling ensures that even the novice body man can make them fit properly, no aerial hole or wing side repeater hole. Ca...

These wings have the original round headlamp hole which is okay unless you have the dipping headlamps fitted to some export models and MPI cars--You will have to use the genuine wing if you have dipping headlamps.See BMP455 for cars with...

Body side rear lower w/arch to rear section of bodyside repair L/H. 220mm tall.

Non genuine R/H Van inner sill. Only made as an after market replacement as no genuine part was ever available seperately. Best one on the market for a comlplete inner sill replacement panel. For Mk1 VAN