£275.00 exc vat
£330.00 inc vat
now
£233.75 exc vat
£280.50 inc vat
In stock
£275.00 exc vat
£330.00 inc vat
now
£233.75 exc vat
£280.50 inc vat
In stockRecommended usage 1 x CZH569 to fit one mini.
This Non genuine pattern panel has the holes for windscreen wipers and jets with barely an inch of pillar.
On cars from 1992/3 on check the original windscreen drain channel as the VIN numbers were stamped above the clutch master cylinder-wi...
Really a built up half front end for the mini clubman, consists of a lower panel with headlamp panels,slam panel and stiffener between the front and slam panel. 76 ON--no inner or outer wings
Really a built up half front end for the mini clubman, consists of a lower panel with headlamp panels,slam panel and stiffener between the front and slam panel,
but not inner or outer wings
Full length inner wing for the R/H on mini clubman.
The only bonnet landing panel available for the clubman shape body for a long time this part is perfect in every detail and was used on the heritage bodyshells.
A Genuine panel is now available from BL Heritage CZH149.
...
A non genuine panel made for repairing the corner of the windscreen panel which is prone to rust from water splashing up from underneath the front wheel arch.
Experience has shown its easier to fit the genuine panel HMP441001 al...
You can spend hours cutting out rust and patching holes, but why bother? These reproduction floor pans extend the full width with vertical flanges for easy installation and fairly well represent the original stamping. They have added metal to include...
Only this genuine wing is now available for the mini clubman but you will probably require the headlamp backing panel CZH120
Only this genuine wing is now available for the mini clubman but you will probably require the headlamp backing panel CZH121
You can spend hours cutting out rust and patching holes, but why bother? These reproduction floor pans extend the full width with vertical flanges for easy installation, and fairly well represent the original stamping. They have added metal to includ...
THIS PANEL PROTECTS THE UNDERSIDE OF THE WINDSCREEN VALANCE UNDER THE FRONT WING SECTION also fitted on the inner wing panel 14A8346/7
1970 on, cars with internal hinges and wind up windows
This repair R/H panel has holes for the hinges on A post and overlaps 6" at top tapering to 9" at bottom (150mm-215mm) onto the wheel arch section.
Also has the first section of...
lower section known as front panel for the clubman range only.his is the rubber monted subframe type as fitted from 1976 on-the earlier type which bolted direct to the subframe is CZH563
Genuine panel that has the holes for wipers and jets with only a few inches of pillar which is basically the area that rots. Also referred to as the windscreen scuttle lower panel. Fitting the genuine type ensures you should get a better windscreen a...
THIS PANEL PROTECTS THE UNDERSIDE OF THE WINDSCREEN VALANCE UNDER THE FRONT WING SECTION also fitted on the inner wing panel 14A8346/7
For Minis with sliding windows and external door hinges These genuine R/H outer A panels fit over the extra inner panel which have brackets on to reinforce the exterior hinges. If the outside one is rotten you can guarantee the i...
Genuine door hinge panel L/H for all MK3 Minis with internal hinges and doors that have wind up windows. Although it is a single wall panel it still has a tendency to develop rust spots so the trade prefer the best fitting thicker upgraded [link]ALA5...
the complete windscreen surround panel up to the roof but see HMP441001 for the part that rusts
This is the engine stabiliser bar original lower bracket that is welded on the
engine bay bulkhead. This part often breaks away when the engine has been rocking around through poor maintenance of engine mounts and bushes.
The upper...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.