£106.00 exc vat
£127.20 inc vat
now
£90.10 exc vat
£108.12 inc vat
In stock
Has the headlamp retaining ring for dipping headlamps
£106.00 exc vat
£127.20 inc vat
now
£90.10 exc vat
£108.12 inc vat
In stockRecommended usage 1 x ASB360010 to fit one mini.
Small angled bracket fitted by factory to stiffen front wings to A panels
These wings have the original round headlamp hole which is okay unless you have the dipping headlamps fitted to some export models and MPI cars--You will have to use the genuine wing if you have dipping headlamps.See BMP455 for cars with...
Fits all minis with side repeater lamps and an aerial hole from 1988 until 1996 except export models with adjusting headlamps. After 1997 ASB360010 should be used, which has no aerial hole, and a recess for the dipping headlight motor. ...
Floor pan for Mini van/estate with no x member for remote change gearbox. Non Genuine. For saloon see 14A6491
picture is just to show what you get but bulge on centre tunnel for starter button appears to be on wrong side as this...
part inner wing L/H from Damper bracket mounting pointing forward for SPI modles 1991-96 with large round electric radiatore fan hole
NON genuine panel
A post and inner wing repair panel 8" wide for Mk1/2 saloon and MK1 Van/pickup
R/H side--6" from a post section
A post and inner wing repair panel 8" wide for Mk1/2 saloon and MK1 Van/pickup
L/H side-6" from A post section
O/S/F wing t for 1996 on cars. THIS WING STILL NEEDS MODIFYING to allow for fitting of Sportspac arches and 13" wheels. After trimming/cutting to size remember to replace or renew the stiffener lip ALR360380
Has the headlamp re...
L/H Inner hinge type A post repair panel with hinge fitting holes mini, MK3
this is a genuine heritage part.
R/H Inner hinge type A post repair panel with hinge fitting holes mini, MK3
this is a genuine heritage part.
This Non genuine pattern panel has the holes for windscreen wipers and jets with barely an inch of pillar.
On cars from 1992/3 on check the original windscreen drain channel as the VIN numbers were stamped above the clutch master cylinder-wi...
Reproduction version os ASJ360070. For the twin point only as it changed shape to accommodate the front mounted radiator and different bonnet fittings.
For vehicles with external hinges and sliding type windows this is a full inner front wing with the wheel arch panel. The panel is what that the outer A panels for the hinges attach to.This is the left hand pane wing with radiator vent slats but not ...
For vehicles with external hinges and sliding type windows this is a full inner front wing with the wheel arch panel. The panel is what that the outer A panels for the hinges attach to. This is the right hand panel made by Heritage but not 100% perfe...
Part inner wing L/H from Damper bracket mounting points forward. MK1/2/3 except Clubman. This panel has radiator cooling slats as fitted to 1991
NON genuine panel only as part panel
part inner wing R/H from Damper bracket mounting points forward MK2/3 except Clubman. 1969-91 not Mk1/2 as it has air hole in side
NON genuine panel
If you fit 13" wheels and need to cut the wings away for clearance these are the reinforcements strips Rover used on the cars with Sportspack arches.
see Downloads on web site for diagrams on where to cut wings and A panels under part number...
Aftermarket wings do the job at a fraction of the cost of originals. This right front wing for the Mini will fit all MKI, II, III, IV. A slight difference exists between the early and the later models as to headlamp mounting holes. These reproduction...
Aftermarket version of the L/H floorpan for 1991 on cars.
This floor was made stronger with smaller heel pad area to prevent vibration and rust and will fit any Rod change gear shift mini but was introduced on the first injection cars in 199...
A non genuine panel made for repairing the corner of the windscreen panel which is prone to rust from water splashing up from underneath the front wheel arch.
Experience has shown its easier to fit the genuine panel HMP441001 al...
You can spend hours cutting out rust and patching holes, but why bother? These reproduction floor pans extend the full width with vertical flanges for easy installation and fairly well represent the original stamping. They have added metal to include...
Only this genuine wing is now available for the mini clubman but you will probably require the headlamp backing panel CZH120
Only this genuine wing is now available for the mini clubman but you will probably require the headlamp backing panel CZH121
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.