£2.91 exc vat
£3.49 inc vat
In stock
£2.91 exc vat
£3.49 inc vat
In stockRecommended usage 1 x FPA904 to fit one mini.
5/16" bore petrol/diesel hose which is sold per metre - also useful as hose for emission or evaporate loss control pipes and expansion tank to radiator use. Suitable for ethanol based products such as modern day fuels. 50psi max. R6 spec.
For use on the red top facet fuel pump that uses 5/16" fuel lines and 1/4 nptf threads.
For use on the red top facet fuel pump that uses 5/16" fuel lines and 1/4 nptf threads.
Before the days of Aeroquip, Minis were fitted with braided steel rubber fuel lines. They should be used in place of rubber for all fuel lines in the engine compartment. They come made to length, with rubber end caps. 1/4" bore size.
This is...
Before the days of Aeroquip, Minis were fitted with braided steel rubber fuel lines. They should be used in place of rubber for all fuel lines in the engine compartment. They come made to length, with rubber end caps. 1/4" bore size.
Orange ...
Special rubber hose 1/4" bore for use on petrol lines, this is in black and not armour plated outside but does have internal reinforcing. Supplied as pre cut 1m length with 2 clips and is safe to use with modern fuels with higher ethanol content. SAE...
Silver top standard 4.0 to 4.5psi, 18 gallons per hour ideal for high output engines using a twin choke carburettor such as Weber and Dellorto with chokes upto 45mm, plus all single SU carbs, plus most twin SU set ups. 1/8" nptf threads and uses 1/4"...
Before the days of Aeroquip, Minis were fitted with braided steel rubber fuel lines. They should be used in place of rubber for all fuel lines in the engine compartment. They come made to length, with rubber end caps. 1/4" bore size.
Orang...
Used on Facet range of solid state and silver fuel pumps SS501/2/3 with 1/8" nptf thread size with 1/4" standard fuel line.
Before the days of Aeroquip, the British were making their own braided steel fuel lines. They should be used in place of rubber for all fuel lines in the engine compartment. They come made to length, with rubber end caps. British Length 7.5"...
Before the days of Aeroquip, Minis were fitted with braided steel rubber fuel lines. They should be used in place of rubber for all fuel lines in the engine compartment. They come made to length, with rubber end caps. 1/4" bore size.
Orange ...
Before the days of Aeroquip, Minis were fitted with braided steel rubber fuel lines. They should be used in place of rubber for all fuel lines in the engine compartment. They come made to length, with rubber end caps.
If you need the 5/16...
Paper gasket for either side of the spacer on all mechanical fuel pumps fitted on the rear of engines. The spacer with gaskets fitted is available as GUG705603GM.
this rubber mounting kit helps to dampen the pump ticking noise as well as acting as an earth
Pumping 40 gallons per hour this is ideal for big bore/stroked engines with twin choke or split carbs over 45mm choke size and will require 5/16" fuel lines
Ideal well priced electric fuel pump for replacing either electric or mechanical pumps when using single HS or HS2 twin carbs 4.00-5.5 PSI delivering 18 gallons per hour.
Other parts required to fit this pump are:
FPA9...
Solid state competition fuel pump with 6-00-7.252PSI 25 GALLONS PER HOUR.
Uses FPA 903 union or FP903A if you wish to upgrade fuel line size for extra flow theses are ideal for single HS4/6 or twin SU carbs.Next step up in pump is [link]STS5...
Genuine Mini Spares product. The seal that goes on the neck of petrol tanks as protection against water intrusion and to also to make the hole look neater, so replace them when they crack or shrink through heat. This is the original fatter type as us...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.