PETROL/RADIATOR HOSE 8MM (5/16") Sold per metre
LPH630

£3.69 exc vat

£4.43 inc vat

In stockIn stock
5/16" bore petrol/diesel hose which is sold per metre - also useful as hose for emission or evaporate loss control pipes and expansion tank to radiator use. Suitable for ethanol based products such as modern day fuels. 50psi max. R6 spec.

£3.69 exc vat

£4.43 inc vat

In stockIn stock

Recommended usage As Required x LPH630 to fit one mini.
Engine Breathers - Qty 1
Emission, Carburettor Fittings and engine controls - Qty 1
Radiator Hoses and Expansion tank MPI - Qty 1

Recommended products

For the LPH630 petrol and emission hose.

For the s/steel braided hoses use ACH5854.

People also bought products

Petrol tank sender unit for saloon models 1959 until 1964 screw on type, for Minis fitted with no voltage stabiliser.

The new adjustable height StayUp® Float is resistant to modern ethanol based Fuels and has a military spec closed cell construction making it puncture proof. The ability to adjust the Float Arm allows for quick and easy minor alterations to Float lev...

5/16" UNF THREAD 2 1/2" LONG bolt commonly used for 21A2838 petrol tank strap

5/16" UNF cage nut as fitted to CZH3241 tank bracket on cars fitted with a 7.5 Gallon fuel tank. Uses 13H7583 bolt

Non Genuine, fits saloons from 1974 until the introduction of injection.

First fitted to 1275GT in 1974 with 12"wheels and all mini saloons from 1980 on

7.5 gallons or 34 litres capacity and the tank is retained by the single stra...

Genuine Mini Spares product. The seal that goes on the neck of petrol tanks as protection against water intrusion and to also to make the hole look neater, so replace them when they crack or shrink through heat. This is the original fatter type as us...

Original 7/16" spring type hose clip as used on later cars (approx 1990 on) for some radiator hoses and fuel lines.

Return spring kit for HS4 carburettor spindle.

Replacement screws and nylon inserts for the Van, Estate and Pick up petrol tanks.

5/16" bore petrol hose for injection cars sold in metre lengths.

Resilient to heat,weather and suitable for ethanol in modern day fuels.100psi max.R9 spec.

5.5 gallon left hand tank with twist in sender unit.

For all mini saloons from 1964 until 1980 except Elf and Hornet. Also except the 1275GT from 1974 which used the later 7.5 gallon tank which became standard fitment to all mini saloons fro...

SPI throttle body spacer - the gaskets are available as LZV1101GASKET

Small hose clip for 1/4" fuel line (our part number PETROLPIPE)

Support bracket for the R/H, genuine Heritage part, can also use our own bracket 21A1329.

Mini Spares Non Genuine version mechanical fuel pump. Brilliant aftermarket alternative for cars pre 1990.

Drives off the camshaft at the rear of the motor. These pumps are generally reliable but when a diaphragm goes bad it can be very bad ...

Non Genuine metal bodied electric fuel pump with metal banjo pipe ends for long life,with blue plastic end. Ethanol tolerant and resistant internals.

This is a cheaper alternatives for the original SU pumps, different to look at and fit but ...

THE ELECTRICAL CIRCUIT FOR THE FUEL PUMP INCORPERATES AN INERTIA FUEL SHUT OFF(ifs) SWITH WHICH WILL STOP FUEL BEING DELIVERED TO THE ENGINE IN THE EVENT OF SUDDEN DECELERATION--It is fitted in the engine compartment, fixed to the bonnet switch brack...

For 1275cc engines after 1990 on with HIF38 carbs.

has a 5/16" (8mm)inlet which makes it unique to this model

The 1990-1 models of the Mini with 1275cc engines and HIF44 carbs use a AZX1817 mechanical fuel pump. Driven ...