£40.00 exc vat
£48.00 inc vat
Out of stock
£40.00 exc vat
£48.00 inc vat
Out of stock
This round gasket has screw holes in to attach the early type saloon petrol sender tank unit to the tank and was used by all vans and estates right up until the end of production. Another use is for the window winder packing gasket CZH753
If you have a van/estate or early mini sender unit in your petrol tank it will be held in by 6 screws 53K165 and these are the special copper washers that go on them. The cork gasket is GUG705711GM
If you have an early Mini saloon or Estate/Van or Pickup with the fuel tank sending unit held in by screws, this is the correct screw for you.
Do not forget the special copper washers also 2A2088 and the cork gasket [link]2H10...
5.5 gallon left hand tank for early mk1 cars pre 1964 with the screw in sender (6 bolts). These are a modified version of our ARA359 tank which are modified by hand to accept the early sender unit (included). The twist and turn type sender unit tank ...
5.5 gallon left hand tank for early mk1 cars pre 1964 with the screw in sender (6 bolts). These are a modified version of our ARA359 tank which are modified by hand to accept the early sender unit (included). The twist and turn type sender unit tank ...
5/16" UNF THREAD 2 1/2" LONG bolt commonly used for 21A2838 petrol tank strap
MPI 7.5 gallon tank has both pump and sender unit holes. Some people use this tank for turbo applications. This tank has the shorter neck with restrictor for lead free fuel nozzles as required by Japan and Germany and uses the thinner neck seal [link...
Genuine Mini Spares product. The seal that goes on the neck of petrol tanks as protection against water intrusion and to also to make the hole look neater, so replace them when they crack or shrink through heat. This is the original fatter type as us...
5.5 gallon left hand tank with twist in sender unit.
For all mini saloons from 1964 until 1980 except Elf and Hornet. Also except the 1275GT from 1974 which used the later 7.5 gallon tank which became standard fitment to all mini saloons fro...
Gasket/seal for mounting the fuel pump to tank for SPI and MPI Mini's
This is a copy of one of the best looking gas caps you will ever add to you car. Polished chrome with a flare. The "'flip top' and 'push button' opening cap was made famous by some of the most historic cars ever raced at such famous tracks as 'Monz...
Vent pipe from petrol tank
late cars were only 765mm or 31" approx, but Mk1 cars were 54"
Designed to look expensive this 60s look cap fits over the genuine Rover locking cap WLD100660 held on by grub screws. Polished alloy finish similar to the Aston or john Cooper cap it is ultra easy to install and looks fantastic. Flip to...
Saloon petrol tank retainer clip for the rubber seal on the sender unit which is ARA1502 .Early tanks had 6 screws holding the sender unit in place and used gasket GUG705711GM
Before the days of Aeroquip, Minis were fitted with braided steel rubber fuel lines. They should be used in place of rubber for all fuel lines in the engine compartment. They come made to length, with rubber end caps. 1/4" bore size.
This is...
Before the days of Aeroquip, Minis were fitted with braided steel rubber fuel lines. They should be used in place of rubber for all fuel lines in the engine compartment. They come made to length, with rubber end caps. 1/4" bore size.
Orange ...
Special rubber hose 1/4" bore for use on petrol lines, this is in black and not armour plated outside but does have internal reinforcing. Supplied as pre cut 1m length with 2 clips and is safe to use with modern fuels with higher ethanol content. SAE...
Sponge like cushioning seal for all minis between the tank neck and the body plus the minivan/estat/pickup petrol tank where it goes between and tank and the the floor/shroud.
This is the thinner type seal as used on the twin point injection cars and is usefull on earlier cars when fitting altenative petrol caps that require more of the neck exposed to allow fitment.
Cooper S Right Hand Tank. Our new perfect fit and shape tank is now in stock. No unsightly "stretch" marks as seen on other tanks that are available, this is a perfect authentic item we are proud of. Approx 5.5 gallon.
See MS82 ...
If you have an early Mini saloon or Estate/Van or Pickup with the fuel tank sending unit held in by screws, this is the correct screw for you.
Do not forget the special copper washers also 2A2088 and the cork gasket [link]2H10...
Special clip for all our braided s/steel petrol hoses.14mm to 16mm.
If you have a van/estate or early mini sender unit in your petrol tank it will be held in by 6 screws 53K165 and these are the special copper washers that go on them. The cork gasket is GUG705711GM
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.