7.5" BRAIDED PETROL PIPE 1/4" BORE
PPK3

£3.02 exc vat

£3.62 inc vat

In stockIn stock
Before the days of Aeroquip, the British were making their own braided steel fuel lines. They should be used in place of rubber for all fuel lines in the engine compartment. They come made to length, with rubber end caps. British Length 7.5"...

£3.02 exc vat

£3.62 inc vat

In stockIn stock

Recommended usage 1 x PPK3 to fit one mini.
Fuel Pumps & Petrol Pipe - Qty 1
Fuel Tanks and Pumps - Qty 1
Fuel Tanks - Qty 1

Recommended products

Special clip for all our braided s/steel petrol hoses.14mm to 16mm.

People also bought products

This is the original type of needle valve that governs the plastic fuel float in your SU carb.

An alternative better upgraded version is available as CA90.

Petrol tank sender unit for saloon models 1959 until 1964 screw on type, for Minis fitted with no voltage stabiliser.

The new adjustable height StayUp® Float is resistant to modern ethanol based Fuels and has a military spec closed cell construction making it puncture proof. The ability to adjust the Float Arm allows for quick and easy minor alterations to Float lev...

5/16" UNF THREAD 2 1/2" LONG bolt commonly used for 21A2838 petrol tank strap

5/16" UNF cage nut as fitted to CZH3241 tank bracket on cars fitted with a 7.5 Gallon fuel tank. Uses 13H7583 bolt

Non Genuine, fits saloons from 1974 until the introduction of injection.

First fitted to 1275GT in 1974 with 12"wheels and all mini saloons from 1980 on

7.5 gallons or 34 litres capacity and the tank is retained by the single stra...

Genuine Mini Spares product. The seal that goes on the neck of petrol tanks as protection against water intrusion and to also to make the hole look neater, so replace them when they crack or shrink through heat. This is the original fatter type as us...

Original 7/16" spring type hose clip as used on later cars (approx 1990 on) for some radiator hoses and fuel lines.

Return spring kit for HS4 carburettor spindle.

Replacement screws and nylon inserts for the Van, Estate and Pick up petrol tanks.

Also denoted by its black plastic base. Twin HS4 carbs have 30 degree float bowl angles and therefore this jet is easier to fit as it is longer. L/H carb uses AUD9098A std single HS2 jet.



For...

5/16" bore petrol hose for injection cars sold in metre lengths.

Resilient to heat,weather and suitable for ethanol in modern day fuels.100psi max.R9 spec.

The main cause of failure is water in the pump. This is caused by modern ethanol fuels. Be sure to clean the tank before fitting and drive your mini more to avoid water build up.

Replacement pump only for the WFX100810 (doesn't...

5.5 gallon left hand tank with twist in sender unit.

For all mini saloons from 1964 until 1980 except Elf and Hornet. Also except the 1275GT from 1974 which used the later 7.5 gallon tank which became standard fitment to all mini saloons fro...

Small hose clip for 1/4" fuel line (our part number PETROLPIPE)

Support bracket for the R/H, genuine Heritage part, can also use our own bracket 21A1329.

Mini Spares Non Genuine version mechanical fuel pump. Brilliant aftermarket alternative for cars pre 1990.

Drives off the camshaft at the rear of the motor. These pumps are generally reliable but when a diaphragm goes bad it can be very bad ...

Non Genuine metal bodied electric fuel pump with metal banjo pipe ends for long life,with blue plastic end. Ethanol tolerant and resistant internals.

This is a cheaper alternatives for the original SU pumps, different to look at and fit but ...