EXHAUST REAR BRACKET 1275GT & S PLUS RC40 (REAR)
GEX7249

£1.55 exc vat

£1.86 inc vat

In stockIn stock
This is the hanger on the rear of the rear subframe for all Coopers and cars with an RC40 exhaust system. The u bolt to fix this to the exhaust is GEX9007.

All the parts to hang RC40 exhausts systems are available in a kit RC40FK.

Attaches to the cotton reel mountings (GEX7251) and it is recommended to fit 2 of these as per the bracket holes as originally they only used one of the mountings. You might need to drill another hole in the subframe.

£1.55 exc vat

£1.86 inc vat

In stockIn stock

Recommended usage 1 x GEX7249 to fit one mini.
Exhaust RC40 1275GT / Cooper S - Qty 1

Recommended products

Exhaust hanger clamp for 1.75" pipe as per RC40 etc.

Engine mounting to subframe bolt (2 per mounting). Some customers find longer bolt GFK5185 easier to use (1"long).

The very rear bobbin type mounting rubber on every mini made until the introduction of a rubber hanger strap in 1992. When the RC40 or similar systems are fitted, 2 will be required.

See C-19G3258 for larger upgrade...

Alternative products

Complete mounting kit for the RC40 exhaust. Includes all new rubber mounts, brackets and clamps.

Kit products

Complete mounting kit for the RC40 exhaust. Includes all new rubber mounts, brackets and clamps.

People also bought products

Exhaust manifold to downpipe clamp. For 32mm o/d pipe size.

The key to eliminating exhaust leaks at the manifold flange is the clamp. These cast clamps are the best style to use. A real piece of kit to use eradicating a multitude of likely p...

The very rear bobbin type mounting rubber on every mini made until the introduction of a rubber hanger strap in 1992. When the RC40 or similar systems are fitted, 2 will be required. This is a stronger poly version.

This sleeve will allow an 1"3/4 rear box to fit a standard bore front pipe of a 998cc mini. The large end fits into the RC40 and the smaller end accepts the 1.25" diameter as standard 850/998 exhaust pipe bore

This is the clamp on the cooper freeflow manifold to clamp it to the engine for extra support, supplied with tag.

Original exhaust bracket for rod change gearbox but later on Rover reverted back to GEX7526 which seemed a bit of a backward cost cutting exercise.

THE M10 METRIC NUT THAT SCREWS ON THE THREAD BOLTS OF THE CATALYLITIC CONVERTER

Exhaust centre strap that hangs from the mounting on the centre of the rear subframe, for saloon models only as the van is longer(GEX7273).

The clip on the exhaust that this attaches to is GEX7052 and is usually on a new exhaust...

Middle exhaust mounting, bolts on to the front of the rear subframe and is the central or first of the rubber mountings. see GEX7081POLY for Poly type or if you are fed up with breakages see C-19G3257.The original Genuine pa...

This is a bolt on conversion bracket to fit on the rear of the rear subframe to take the later type rubber strap mounted exhaust systems.Later subframes 1991 on had these parts welded in position.

Exhaust manifold to downpipe clamp.

The key to eliminating exhaust leaks at the manifold flange is the clamp. These new clamps include proper brass nuts and support washers. Fits most 850cc, 948cc, 998 etc. Those engines with single carb an...

Twin Down pipe clamp for Carb Coopers 1990 on wards, and Metro's.

Also used as a single clamp on manifold for cars fitted with HIF38 carb cars from 1991 on.

For the medium bore Maniflow LCB Y piece or AN180V. 48mm ID

The center exhaust hanger takes a lot of abuse during hard acceleration or if you're low enough to bottom out on bumps. This mount has a through metal bolt to keep it intact.

Special tin plate type of gasket that goes between the manifold and exhaust downpipes on all injection cars.

The very rear bobbin type mounting rubber on every mini made until the introduction of a rubber hanger strap in 1992. When the RC40 or similar systems are fitted, 2 will be required.

See C-19G3258 for larger upgrade...

This popular size clamp fits the y piece where it joins the manifold on all our standard long centre branch exhaust manifolds. Sold singly.

Mounting in poly for the exhaust on the front section of the rear subframe. Now orange in colour.