£4.16 exc vat
£4.99 inc vat
In stock
£4.16 exc vat
£4.99 inc vat
In stockRecommended usage 1 x GTS106 to fit one mini.
Forget all the universal shape gaskets available - this is the original correct shape made out of thick gasket paper.
Genuine version of the thermostat gasket for all A series. Black one side and red the other they are fitted black side to the head. Green to the thermostat.
We have no evidence as yet that they last longer but do look good.
See [lin...
This thermostat housing fitting kit, suitable for all single tier thermostat housings. Comes with new studs, nuts, washers and Klinger thermostat housing gasket
Similar to C-ARA4401 but supplied without the fan controller. This kit is ideal if you want to wire the fan to a fan switch.
Long lasting silicon by pass hose between cylinder head and water pump.
These are easy to cut and slide on easier than the old conventional rubber type.
It has been made this length to fit 1275cc engines which used the longest hose....
MPI cast thermostat housing. Useful for any radiator fitted in front of the engine this housing has an outlet pipe for the expansion tank.
The original tooling is no longer available and believed scrapped but this is a very good reproductio...
Replacement plug and washer for Minispares 2 core and 4 core radiators
Silicone hose kit for 998 vehicles from 1989 onwards that were equipped with the plastic inline heater valve, comes complete with moulded heater take off pipe and 5/8 heater pipe.
Silicone hose kit for 998 vehicles from 1989 onwards that were equipped with the plastic inline heater valve, comes complete with moulded heater take off pipe and 5/8 heater pipe.
Heater hose that comes from the cylinder head take off to the plastic inline heater valve on 998s 1988 on - this can also be used with a heater take off on 1275cc engines.
Heater hose that comes from the cylinder head take off to the plastic inline heater valve on 998s 1988 on - this can also be used with a heater take off on 1275cc engines.
Original 7/16" spring type hose clip as used on later cars (approx 1990 on) for some radiator hoses and fuel lines.
MPI only. 3 YEAR GUARANTEE-UK made.Large impeller higher capacity water pump. Mini Spares procured product as original Rover Airtex tooling has been scrapped.
Fitted with a PPS, glass filled plastic impeller as used by Jaguar and Aston Marti...
3 YEAR GUARANTEE-UK made.Large impeller higher capacity water pump with top quality die cast body . Mini Spares procured product as the original superb Rover Airtex tooling has been scrapped.
Fitted with a PPS, glass filled plastic impeller...
3 YEAR GUARANTEE-UK made. Large impeller higher capacity water pump with a high quality die cast body. A Mini Spares procured product as the original superb Rover Airtex tooling has been scrapped.
Fitted with a PPS, glass filled plastic impe...
Spring clip for securing the top hose on MPI front mounted radiator models, now in stainless steel.
Spring clip for securing the top hose on MPI front mounted radiator models.
This is the metric nut needed for PQR10028 tensioner as fitted to all mpi mini's.
Silicone heater hose, 1 Metre for cars with the inline type heater valve or a straight take off on the cylinder head as fitted to post 1984 cars.
Silicone heater hose, 39" for cars with the inline type heater valve or a straight take off on the cylinder head as fitted to post 1988 cars.
Silicone heater hose, 39")1metre) for cars with the inline type heater valve or a straight take off on the cylinder head as fitted to post 1984 cars.
Designed to reduce the horsepower drain and slow down the water moving through the radiator to allow it time to cool, its very important for the higher RPMs we run today. This oversize pulley is 4.2" diameter, earlier cars used a 3.875" wide pulley. ...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.